manualshive.com logo in svg

HP 6125G, Command Reference Manual, Page: 266 / 426

Share
Download
HP 6125G Command Reference Manual Download Page 266

 

254 

Use 

undo

 

port multicast-vlan ipv6

 to restore the default.  

By default, a port does not belong to any IPv6 multicast VLAN.  
A port can belong to only one IPv6 multicast VLAN. 

Examples 

# Assign GigabitEthernet 1/0/1 to IPv6 multicast VLAN 100. 

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] port multicast-vlan ipv6 100 

subvlan (IPv6 multicast VLAN view) 

Syntax 

subvlan 

vlan-list

 

undo

 

subvlan

 { 

all

 | 

vlan-list

 }

 

View 

IPv6 multicast VLAN view 

Default level 

2: System level 

Parameters 

vlan-list

: Specifies a VLAN in the form of 

vlan-id

, or a VLAN range in the form of 

start-vlan-id

 to 

end-vlan-id

, where the end VLAN ID must be greater than the start VLAN ID. The value range of a VLAN 

ID is 1 to 4094. 

all

: Specifies all the sub-VLANs of the current IPv6 multicast VLAN.  

Description 

Use 

subvlan

 to configure sub-VLANs for the current IPv6 multicast VLAN.  

Use 

undo

 

subvlan 

to remove the specified sub-VLANs or all sub-VLANs from the current IPv6 multicast 

VLAN. 
An IPv6 multicast VLAN has no sub-VLANs by default.  
The VLANs to be configured as the sub-VLANs of the IPv6 multicast VLAN must exist and must not be IPv6 

multicast VLANs or sub-VLANs of any other IPv6 multicast VLAN. 
The number of sub-VLANs of the IPv6 multicast VLAN must not exceed the system-defined limit.  

Examples 

# Configure VLAN 10 through VLAN 15 as sub-VLANs of IPv6 multicast VLAN 100.  

<Sysname> system-view 

[Sysname] multicast-vlan ipv6 100 

[Sysname-ipv6-mvlan-100] subvlan 10 to 15 

Summary of Contents for 6125G











































































































































































































































































































































































































































Reviews:

No comments