manualshive.com logo in svg

HP 6125G, Command Reference Manual, Page: 145 / 426

Share
Download
HP 6125G Command Reference Manual Download Page 145

 

133 

<Sysname> system-view 

[Sysname] interface vlan-interface 100 

[Sysname-Vlan-interface100] pim timer graft-retry 80 

pim timer hello 

Syntax 

pim timer hello

 

interval

 

undo pim timer hello 

View 

Interface view 

Default level 

2: System level 

Parameters 

interval

: Hello interval in seconds, with an effective range of 1 to 2,147,483,647.  

Description 

Use 

pim timer hello

 to configure the interval at which hello messages are sent on the current interface.  

Use 

undo pim timer hello 

to restore the default.  

By default, hello messages are sent at the interval of 30 seconds.  
Related commands: 

timer hello

.  

Examples 

# Set the hello interval to 40 seconds on VLAN-interface 100.  

<Sysname> system-view 

[Sysname] interface vlan-interface 100 

[Sysname-Vlan-interface100] pim timer hello 40 

pim timer join-prune 

Syntax 

pim timer join-prune 

interval 

undo pim timer join-prune 

View 

Interface view 

Default level 

2: System level 

Parameters 

interval

: Join/prune interval in seconds, with an effective range of 1 to 2,147,483,647.  

Description 

Use 

pim timer join-prune

 to configure the interval at which join/prune messages are sent on the current 

interface.  

Summary of Contents for 6125G











































































































































































































































































































































































































































Reviews:

No comments