HP 6125G Command Reference Manual Download Page 23

Page: 23 / 426

By default, this function is disabled.
This command works only in IGMP snooping–enabled VLANs.
Related commands:

display igmp-snooping host

and

igmp-snooping host-tracking

Examples

# Enable the IGMP snooping host tracking function globally.

<Sysname> system-view

[Sysname] igmp-snooping

[Sysname-igmp-snooping] host-tracking

igmp-snooping

Syntax

igmp-snooping
undo igmp-snooping

View

System view

Default level

2: System level

Parameters

None

Description

Use

igmp-snooping

to enable IGMP snooping globally and enter IGMP-snooping view.

Use

undo igmp-snooping

to disable IGMP snooping globally.

By default, IGMP snooping is disabled.
Related commands:

igmp-snooping enable

Examples

# Enable IGMP snooping globally and enter IGMP-snooping view.

<Sysname> system-view

[Sysname] igmp-snooping

[Sysname-igmp-snooping]

igmp-snooping dot1p-priority

Syntax

igmp-snooping dot1p-priority

priority-number

undo igmp-snooping dot1p-priority

View

VLAN view

Default level

2: System level

Summary of Contents for 6125G











































































































































































































































































































































































































































Search results

Summary of Contents for 6125G

Reviews:

Related manuals for 6125G

Brands by name

Popular brands

HP 6125G, Command Reference Manual

Search results

Summary of Contents for 6125G

Reviews:

Related manuals for 6125G

Brands by name

Popular brands