HP 6125G Command Reference Manual Download Page 276

Page: 276 / 426

264

View

System view

Default level

2: System level

Parameters

source

: Specifies IPv6 multicast load splitting on a per-source basis.

source-group

: Specifies IPv6 multicast load splitting on a per-source and per-group basis.

Description

Use

multicast ipv6 load-splitting

to enable load splitting of IPv6 multicast traffic.

Use

undo multicast ipv6 load-splitting

to disable load splitting of IPv6 multicast traffic.

By default, load splitting of IPv6 multicast traffic is disabled.

Examples

# Enable load splitting of IPv6 multicast traffic on a per-source basis.

<Sysname> system-view

[Sysname] multicast ipv6 load-splitting source

multicast ipv6 longest-match

Syntax

multicast ipv6 longest-match
undo multicast ipv6 longest-match

View

System view

Default level

2: System level

Parameters

None

Description

Use

multicast ipv6 longest-match

to configure RPF route selection based on the longest match principle,

namely, to select the route with the longest prefix as the RPF route.
Use

undo multicast ipv6 longest-match

to restore the default.

By default, the route with the highest priority is selected as the RPF route.

Examples

# Configure RPF route selection based on the longest match.

<Sysname> system-view

[Sysname] multicast ipv6 longest-match

Summary of Contents for 6125G











































































































































































































































































































































































































































Search results

Summary of Contents for 6125G

Reviews:

HP 6125G, Command Reference Manual, Page: 276 / 426

Search results

Summary of Contents for 6125G

Reviews: