HP 6125G Command Reference Manual Download Page 263

Page: 263 / 426

251

IPv6 multicast VLAN configuration commands

display multicast-vlan ipv6

Syntax

display multicast-vlan

ipv6

[

vlan-id

] [

{

begin

exclude

include

}

regular-expression

]

View

Any view

Default level

1: Monitor level

Parameters

vlan-id

: Specifies an IPv6 multicast VLAN, in the range of 1 to 4094. If this argument is not specified, this

command displays information about all IPv6 multicast VLANs.

: Filters command output by specifying a regular expression. For more information about regular

expressions, see

Fundamentals Configuration Guide

begin

: Displays the first line that matches the specified regular expression and all lines that follow.

exclude

: Displays all lines that do not match the specified regular expression.

include

: Displays all lines that match the specified regular expression.

regular-expression

: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use

display multicast-vlan ipv6

to display information about the specified IPv6 multicast VLAN or all IPv6

multicast VLANs.

Examples

# Display information about all IPv6 multicast VLANs.

<Sysname> display multicast-vlan ipv6

Total 2 IPv6 multicast-vlan(s)

IPv6 Multicast vlan 100

subvlan list:

vlan 2 4-6

port list:

no port

IPv6 Multicast vlan 200

subvlan list:

no subvlan

port list:

GE1/0/1 GE1/0/2

Summary of Contents for 6125G











































































































































































































































































































































































































































Search results

Summary of Contents for 6125G

Reviews:

HP 6125G, Command Reference Manual, Page: 263 / 426

Search results

Summary of Contents for 6125G

Reviews: