HP 6125G Command Reference Manual Download Page 168

Page: 168 / 426

156

peer mesh-group

Syntax

peer

peer-address

mesh-group

name

undo peer

peer-address

mesh-group

View

MSDP view

Default level

2: System level

Parameters

peer-address

: Specifies an MSDP peer address.

name

: Specifies a mesh group name, a case-sensitive string of 1 to 32 characters. A mesh group name

must not contain any space.

Description

Use

peer mesh-group

to configure an MSDP peer as a mesh group member.

Use

undo

peer mesh-group

to remove an MSDP peer as a mesh group member.

By default, an MSDP peer does not belong to any mesh group.

Examples

# Configure the MSDP peer with the IP address of 125.10.7.6 as a member of the mesh group "Group1".

<Sysname> system-view

[Sysname] msdp

[Sysname-msdp] peer 125.10.7.6 mesh-group Group1

peer minimum-ttl

Syntax

peer

peer-address

minimum-ttl

ttl-value

undo

peer

peer-address

minimum-ttl

View

MSDP view

Default level

2: System level

Parameters

peer-address

: Specifies an MSDP peer address.

ttl-value

: Specifies a Time-to-Live (TTL) threshold, in the range of 0 to 255.

Description

Use

peer minimum-ttl

to configure the TTL threshold for multicast data packet encapsulation in SA

messages.
Use

undo

peer minimum-ttl

to restore the default.

Summary of Contents for 6125G











































































































































































































































































































































































































































Search results

Summary of Contents for 6125G

Reviews:

Related manuals for 6125G

Brands by name

Popular brands

HP 6125G, Command Reference Manual

Search results

Summary of Contents for 6125G

Reviews:

Related manuals for 6125G

Brands by name

Popular brands