manualshive.com logo in svg

Hospira LifeCare XL Series, Technical & Service Manual

Share
Download
Hospira LifeCare XL Series Technical & Service Manual Download Page 100

7.2

REPLACEMENT PROCEDURES

Technical Service Manual

7 - 21

430-00587-008 (Rev. 2/05)

Figure 7-9.

AC Power Cord (115 VAC - Plum XLM)

7.2.8.5

AC (MAINS) POWER CORD REPLACEMENT (INTERNATIONAL)

No tools are required for this procedure.

The replacement part for this procedure is:

Cordset, AC Power, Hospital, International

To replace the AC (mains) power cord, refer to 

Figure 7-10, AC Power Cord (220 VAC - Plum

XLM)

 or 

Figure 7-11, AC Power Cord (220 VAC - Plum XLM)

, then disconnect the power cord

from the rear of the infusion system and connect the replacement power cord.

Replacement of the AC (mains) power cord is a routine maintenance procedure and no
verification procedure is normally required. However, if the infusion system may have been
damaged during this procedure, perform the PVT in 

Section 5.2

.

EMI

SHIELD

REAR ENCLOSURE

AC POWER

 CORD

DATAPORT/GROUND

CABLE ASSEMBLY

04K01045

STRAIN 

RELIEF

BUSHING

POWER 

SUPPLY

PWA

FLAT WASHER (2)

6-32 KEP NUT (4)

GROUND WIRE (2)

6-32 x 1 HEX

HEAD SCREW

Summary of Contents for LifeCare XL Series























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands