Horizon Hobby ??11, Operation Manual

Page: 11 / 124

9
▋
Receiver▋Connections
Receiver Connections to the servos and the power supply
JR labels the channels on the receiver with names rather than numbers. From this point onward in the manual, the
receiver channels will be described using their names.
▋ ▋ Connection▋list▋to▋Receiver
Strong
Reception
RX
RX
RX
RX
×
Receiving Sensitivity (High)
RX
RX
RG Cable 150
Remote Antenna
Built-in Antenna
▼ Front Face
▲ Rear Face
RA01T Side View
※When using a Gyro, carry out
the connection according to
the Gyro operation manual.
RX battery
BIND PLUG
Bind plug
Y-Harness
Switch harness
SENSOR
Rudder channel
Auxiliary channel
Auxiliary channel
Auxiliary channel
Auxiliary channel
Gear channel
Elevator channel
Aileron channel
Throttle channel
Auxiliary channel
Auxiliary channel
RG1131B Receiver
[XG7の場合]
バインド出力
画面
Location of LED light
Binding terminal
Bind plug
1. Are the transmitter and receiver batteries fully charged?
2. Is the remote antenna securely connected?
3. Is the distance between the transmitter and receiver too close?
4. When the procedure is carried out on the top of a desk or
bench top that is made from metal, the binding procedure
may not be successful.
If the bind process or range check is not successful,
check the following items:
Please note that when the model or model type is
changed in the transmitter, re-binding will be required.
Never fly the aircraft in Range Check mode.
Be sure that the failsafe settings are set in the
transmitter.
40 meters
[XG7]
ステータスLED
When connecting
sensors, connect a
Y-Harness (sold
separately) to the
(BIND/BATT/SENS)
terminal.
This is used during
the bind procedure.
Insert the connector,
taking adequate care
of the direction.
Weak
Signal
Strong
Reception
Strong
Reception
Weak
Signal
Strong
Reception
※The remote antenna receives data
and also feeds back to the transmitter
(telemetry).
Built-in Antenna
Circuit Board Face
The built-in antenna of the remote antenna is
installed on the surface of the circuit board.
Care will be required in the situation where the
built-in antenna has been installed beside a
shielding material, since the receiving sensitiv-
ity will be considerably degraded.
C o a x i a l p a r t o f t h e
antenna can be bent
however, do not bend it
in a sharp angle. This
will damage the internal
antenna wires.
The antenna part should be installed
in a perfectly straight condition.
Wrong Antenna Installation
If each antenna is installed in parallel, the
receiving efficiency will be reduced.
The arrows show the receiving direction with
regard to the antenna.
Receiving
Sensitivity
(Low)
Material Frame
Receiving
Sensitivity
(High)
Receiving Sensitivity (High)
※Take care not to
damage the anten-
nas projecting from
the aircraft body.
Aircraft body surface made
from shielding material.
Connecting
the battery to a
spare channel
(such as AUX
channel)
⿟ Since the receiver is susceptible to
vibration, shock, and water, anti-vibration
and waterproofing measures should be
implemented.
⿟ If the connectors become detached while
flying, there will be a risk of uncontrolled
operation. Please securely insert all of the
connectors as far as they will go.
⿟ In the situation where relay connectors
(extension leads) are used during
installation rubber sponge should be
wrapped round the connectors to fix them.
Be absolutely sure not to leave the
connectors hanging unsupported.
Receiver Helicopter Airplane Glider
1)
THRO THRO THRO LAILE
2) AILE AILE AILE RAILE
3)
ELEV ELEV ELEV ELEV
4) RUDD RUDD RUDD RUDD
5)
GEAR GYRO GEAR GEAR
6) AUX1 PIT. FLAP FLAP
7)
AUX2 GOV AUX2 AUX2
8) AUX3 NEDL AUX3 AUX3
9)
AUX4 AUX4 AUX4 AUX4
10) AUX5 AUX5 AUX5 AUX5
11)
AUX6 AUX6 AUX6 AUX6
Preparation
XG11.indd 9 12/01/19 12:29