Horizon Hobby ??11, Operation Manual

Page: 89 / 124

87
▋ ▋ Altimeter▋(ALTITUDE)
⿟ UNIT (SCALE)
This selects the units – Meter (m) or Feet (ft). Select
the units as desired.
⿟ Sound: Audio (SOUND1,2,3)
It is possible to select from three (3) types of audio
for different altitude indications. Initially it is set to
inhibit. If desired, set the alert sound depending on
the situation. It is possible to set altitude between 1 〜 2000m in 1.0 meter increments.
Types of Alert:
↑ : When the altitude is greater than the set value.
↓ : When the altitude is less than the set value.
〜 : When flying within the set altitude range.
※ When the alert is set in an altitude range, it can be set between 0.3m 〜 9.9m in 0.3m increments.
If the three (3) conditions overlap, Priority is set as “SOUND3 > SOUND2 > SOUND1”.
⿟ Switch Select (SW SEL)
It is possible to set an Alert to be active by switches or stick position, or a combination of those devices by using
“SW SEL”. Initially it is always turned on.
▋ ▋ Climb▋Indicator▋(VARIOMETER)
⿟ UNIT (SCALE)
This selects the units（m/s, ft/s). Select the units as
desired.
⿟ Audio for Ascent (UP SOUND1,2,3,4)
The Climb Rate can be set in 4 different ranges, with
an alert for each range. Each one of the setting can
have an alert. Initially it is set to “INH”. The Climb
Rate alert can be set between 0.1m/s 〜 3.0m/s, in 0.1m/s increments.
※ If the four (4) conditions overlap, Priority is set as "SOUND4 > SOUND3 > SOUND2 > SOUND1".
⿟ Audio for Descent (DOWN SOUND)
The Descent Rate can be set in 4 different ranges, with an alert for each range. Each one of the setting can have an
alert. Initially it is set to “INH”. The Descent Rate alert can be set between 0.1m/s 〜 3.0m/s, in 0.1m/s increments.
⿟ Switch Select (SW SEL)
It is possible to set the Alert to be active by switches or stick position, or a combination of those devices by using
“SW SEL”. Initially it is always turned on.
▋ ▋ For▋Motive▋Power▋Battery▋(FLIGHT▋PACK)
⿟ Motive Power BatteryAlarm (VOLT-ALARM)
It is possible to set an alert for low Motive Power
Battery voltage. Initially it is set as Inhibited. Set
the alert voltage as desired. The Voltage can be set
between 0.1V 〜 655.3V in 0.1V increments.
⿟ Nominal Capacity Value (CAPACITY)
It is possible to set a Nominal Capacity Value to
match your Motive Power battery capacity. The remaining battery capacity value is displayed by deducting the
consumed capacity value. It can be set between 0mAh 〜 30,000mAh, in 10mAh increments.
⿟ Battery Capacity Alarm (CAPA-ALARM)
It is possible to set a capacity remaining alert based on the Nominal Capacity value of your battery. Initially it is
set as Inhibited. To activate, set a percentage between 0% to 100%. The alarm will sound when this calculated
percent capacity remaining reaches this figure.
ダイヤル
TIPS
調整ポイント表示
ポイント接続を曲線に変更 スティック入力位置と出力位置の数値表示
現在の
フライトモード位置
各調整ポイントの
入力位置と出力位置
ポイントの
追加と削除
注意：
グラフはホバリン
グスロットルやス
ロットルトリムで
変化する場合もあ
ります。
カーブをコピー
By using the Information screen, it is possible to display your desired Telemetry information on the first page, together
with the Timer and Flight Mode selection on a screen that customers can customize so that it is easy to check.
Initially it is set as Inhibited. Select the telemetry information to be displayed, and allocate it to a position on the screen.
▋ ▋ Caution▋Note
⿟ The Telemetry sensor data is ment as an indication only, and therefore we cannot guarantee the accuracy of any
recordings obtained.
System▋List▋
XG11.indd 87 12/01/19 12:30