Rev. 3.0, 04/02, page 783 of 1064
21.2.4
Interrupt Factor Register (SDINT)
The interrupt factor register (SDINT) is a 16-bit register that can be read/written from the CPU.
When a (H-UDI interrupt) command is set in the SDIR (Update-IR) via the H-UDI pin, the
INTREQ bit is set to 1. While SDIR has the “H-UDI interrupt” command, the SDINT register is
connected between H-UDI pins TDI and TDO, and can be read as a 32-bit register. The high 16
bits are 0 and the low 16 bits are SDINT.
Only 0 can be written to the INTREQ bit from the CPU. While this bit is 1, the interrupt request
continues to be generated, and must therefore be cleared to 0 by the interrupt handler. This register
is initialized by
or when in the Test Logic Reset state.
Bit:
15
14
13
12
11
10
9
8
—
—
—
—
—
—
—
—
Initial value:
0
0
0
0
0
0
0
0
R/W:
R
R
R
R
R
R
R
R
Bit:
7
6
5
4
3
2
1
0
—
—
—
—
—
—
—
INTREQ
Initial value:
0
0
0
0
0
0
0
0
R/W:
R
R
R
R
R
R
R
R/W
Bits 15 to 1—
Reserved: These bits always read as 0, and should only be written with 0.
Bit 0—Interrupt Request Bit (INTREQ): Shows the existence of an interrupt request from the
“H-UDI interrupt” command. The interrupt request can be cleared by writing 0 to this bit from the
CPU. When 1 is written to this bit, the existing value is retained.
21.2.5
Boundary Scan Register (SDBSR)
The boundary scan register (SDBSR) is a shift register on the PAD for controlling the chip’s I/O
pins. Using the EXTEST and SAMPLE/PRELOAD commands, it can perform a JTAG (IEEE Std
1149.1)-compatible boundary scan test. Table 21.3 shows the relationship between SH7751 Series
pins and the boundary scan register.
Summary of Contents for SH7751
