Hitachi AMS 2000 Series, Reference Manual

Page: 70 / 262

1–52
Performing CCI Operations
Hitachi AMS 2000 Family Command Control Interface (CCI) Reference Guide
Options
(continued) -fe: This option displays a device serial number and a volume managing number of
the other device to which external LUN is mapped. When no external LUN exists on
the specified port, nothing is displayed. Display example:
Port# /ALPA/C TID# LU# Seq# Num LDEV# P/S Status Fence E-Seq# E-LDEV#

CL1-A ef 0 0 48 85003005 2 256 SMPL - - 85003006 17

CL1-A ef 0 0 49 85003005 2 272 SMPL - - 85003006 23

CL1-A ef 0 0 50 85003005 1 288 SMPL - - 85003006 28
-CLI: Specifies display for command line interface (CLI). This option displays to the
same position that defined number of columns, and displays one header. The
delimiters between columns are displayed as spaces or hyphens (-). Display example:
Port# TargetID# Lun# Seq# Num LDEV# P/S Status P-Seq# P-LDEV#
CL1-A 1 0 85003005 1 0 SMPL - - -
CL1-A 2 2 85003005 1 2 P-VOL PAIR 85003005 26
CL1-A 2 3 85003005 1 3 P-VOL PAIR 85003005 27
-pi<strings>:
Used to change the STDIN of the -find option to argument input. If this
option is specified, the STDIN becomes invalid. Specify <strings> in less than or
equal to 255 characters.
-find [op] [MU#]:
Executes the operation specified in [op] using a special file (raw
device file) provided via STDIN. If the -pi <strings> option is specified, the STDIN
becomes invalid and changes to <strings>.

Restriction: Special files via STDIN are specified in the following ways: 
HP-UX systems: /dev/rdsk/*, /dev/rdisk/disk*, /dev/rcdisk/disk* 
Solaris systems: /dev/rdsk/*s2, c*s2 
AIX systems: /dev/rhdisk*, /dev/hdisk*, hdisk* 
Linux systems: /dev/sd*, /dev/rd*, /dev/raw/raw* 
Tru64 UNIX systems: /dev/rdisk/dsk*c 
IRIX systems: /dev/rdsk/*vol, /dev/rdsk/node_wwn/*vol/*, /dev/dsk/*vol, 
/dev/dsk/node_wwn/*vol/* 
Windows systems: hd0-10, harddisk0, harddisk1... 
(numbers indicate the drive number) 
$LETALL, $Volume, $Phys, D:\Vol(Dms,Dmt, Dmr)X\DskY, 
\Vol(Dms,Dmt, Dmr)X\DskY 
For Windows LDM volumes, refer to the Hitachi AMS 2000 Family Command Control
Interface (CCI) User’s Guide.
-find[g]:
Displays the port, target ID, and LUN (array notation) which was mapped
for LDEV using a special file (raw device file ) provided via STDIN (see Figure 1-39 ).
If target ID and LUN are Unknown for the target device file, you must start HORCM
without a description for HORCM_DEV and HORCM_INST, and should describe the
shown Port, target ID, and LUN for HORCM_DEV. This option also uses the -fx option
to display the LDEV numbers in hexadecimal. -findg option is specified to find host
group and to display LUN.
-find inst:
Obtains the Ser# and LDEV# of the volume using a special file (raw device
file) provided via STDIN, and then checks the consistency with the volume described
in the configuration definition file. Then registers (permits) the special file name to
HORCM, and displays the relation between the configuration definition file. This option
is not usually used because it is automatically used by /etc/hormgr. This option also
uses the -fx option to display the LDEV numbers in hexadecimal (see
Figure 1-40 ). 
Note: When activating HORCM, the CCI automatically registers the device file by
executing raidscan -find inst command. If this command is executed manually even if
the device file has already been registered, a message “The registration has been
canceled due to enough for HORCM.” Is displayed and the command will be rejected.
-find verify [MU#]: Displays the relation between the volumes described in the
configuration definition file after obtaining the Ser# and LDEV# of the volume using a
special file (raw device file). This option also uses the -fx option to display the LDEV
numbers in hexadecimal. This option is effected by the command execution
environment (HORCC_MRCF).
Table 1-18: Raidscan Command Parameters (Continued)
Parameter Value