1–36
Performing CCI Operations
Hitachi AMS 2000 Family Command Control Interface (CCI) Reference Guide
Options
(continued)
-fx:
Displays the LDEV ID as a hexadecimal number.
-fd:
Displays the group-based device file of the configuration file registered in
HORCM and the relation between the groups. If Unknown is displayed in the
DEVICE_FILE shown below, the pair operation (except for the local option) is rejected
as protection mode because the volume is not registered.
Example:
# pairdisplay –g oradb –fd
Group PairVol(L/R) Device_File M,Seq#,LDEV#.P/S,Status, Seq#,P-LDEV# M
oradb oradb1(L) Harddisk1 0 85005013 17.P-VOL COPY,85005013 18 -
oradb oradb1(R) Unknown 0 85005013 ****.------ -------, ------ ----- -
-fe:
Displays discrimination between a SnapShot volume and a ShadowImage
volume and a number of active link paths, and so on by adding them as the last
column. The 80-column format of 80 is neglected. This option will be invalid if the
cascade options (-m all) are specified.
-fw: Used to display the WWN setting to the port instead of a port name. If this
option is specified with “-fe” option at the same line, then “LUN WWN” is displayed
as shown below. If WWN is not computed, then “Unknown” is displayed.
Example:
# pairdisplay -g oradb -fw
# pairdisplay -g oradb -w
Group PairVol(L/R)(WWN , LU-M) ,Seq#,LDEV#.P/S,Status, Seq#,P-LDEV#
M
oradb oradev1(L)(50060e8010200650, 21-0 )85000101 21.P-VOL
PSUS,85000101 20 W
oradb oradev1(R)(50060e8010200654, 20-0 )85000101 20.S-VOL SSUS,-----
21 W
# pairdisplay -g oradb –fwe
Group PairVol(L/R)(WWN , LU-M) ,Seq#,LDEV#.P/S,Status, Seq#,P-LDEV#
M
CTG CM EM E-Seq# E-LDEV# LUN-WWN
oradb oradev1(L)(50060e8010200650, 21-0 )85000101 21.P-VOL
PSUS,85000101 20 W
- N - - - 60060e80102006500510ffa500000014
oradb oradev1(R)(50060e8010200654, 20-0 )85000101 20.S-VOL SSUS,-----
21 W
- N - - - 60060e80102006500510ffa500000015
-CLI:
Used to specify display for command line interface (CLI). This option displays
to the same position that defined number of columns, and displays one header. The
delimiters between columns are displayed as spaces or hyphens (-). Display
example:
# pairdisplay –g homrcf1 –CLI
Group PairVol L/R Port# TID LU-M Seq# LDEV# P/S Status Seq# P-LDEV# M
homrcf1 deva0 L CL1-A 3 5 0 85003005 5 P-VOL PAIR 85003005 3 -
homrcf1 deva1 L CL1-A 3 5 0 85003005 5 SMPL - - - -
homrcf1 deva2 L CL1-A 3 5 0 85003005 5 SMPL - - - -
-v smk (for SnapShot):
This option displays the time (UTC) when the Split-Marker
(a character string with 31 or less characters) is added to the V-VOL and the Split-
Marker as an execution result only for the SnapShot pair that has been split by the
pairsplit -ms command.
-v pid (for SnapShot only): This option displays the pair volume name or the
information on the pool which the pair specified by <raw_device> uses. The
information on the pool of the local side is displayed on the 1st line, and the
information on the pool of the remote side is displayed on the 2nd line. If executing
it to the SnapShot pair, the displays of the 1st line and the 2nd line become equal.
Table 1-12: Pairdisplay Command Parameters (Continued)
Parameter
Value
Summary of Contents for AMS 2000 Series
Page 6: ...vi Table of Contents Hitachi AMS 2000 Family Command Control Interface CCI Reference Guide ...
Page 244: ...4 18 Command options Hitachi AMS 2000 Family Command Control Interface CCI Reference Guide ...
Page 261: ...1 Hitachi AMS 2000 Family Command Control Interface CCI Reference Guide ...
