GSSI SIR 4000 Manual Download | Manualshive

Page: 15 / 163

background image

Geophysical Survey Systems, Inc.

SIR® 4000

Manual

MN72-433 Rev F

9

2.2: Introduction Screen

After the SIR 4000 boots up and goes past the splash screen, you will see the Introduction screen. This
screen allows you to select from the following options and modes. It also includes a toolbar at the bottom
and status information. Note: the setup screen will change depending on whether a digital or analog
antenna is connected. If no antenna is connected, only Playback Mode is available.

Modes

The following modes have different options available in the subsequent Setup display based upon
application and whether 2D or 3D data is being collected. Applications that are in development will be
greyed out in the Introduction screen.

Digital 2D (Digital Antennas Only)

With Digital 2D Mode the user has complete control over all 2D data collection parameters. All
parameters in this mode are customizable, whereas in an application specific mode some options are
limited based on what is necessary and customary for successful data collection.

Digital 3D (Digital Antennas Only)

In Digital 3D Mode the user has all of the same controls from Digital 2D Mode as well as options to
setup, collect, and playback data in a 3D grid.

Expert Mode

With Expert Mode the user has complete control over all 2D data collection parameters. All parameters in
this mode are customizable, whereas in an application specific mode some options are limited based on
what is necessary and customary for successful data collection.

Quick 3D

In Quick 3D Mode the user has all of the same controls from Expert Mode as well as options to setup,
collect, and playback data in a 3D grid.

«
...
13
14
15
16
17
...
»

Summary of Contents for SIR 4000




































































































































































Reviews:

No comments

Related manuals for SIR 4000

Brand: Waterway Pages: 16

Brand: Aalborg Pages: 15

Brand: Aalborg Pages: 48

Brand: MacDon Pages: 32

Brand: K&K Pages: 6

TruPortal TP-ADD-1DIP

Brand: Interlogix Pages: 9

Brand: EVERSPRING Pages: 3

Brand: elsner elektronik Pages: 2

769N FireLock NXT Series

Brand: Victaulic Pages: 40

Brand: IBCcontrol Pages: 16

Entelli-Switch 250

Brand: GE Pages: 32

Alicat Scientific MC

Brand: Halma Pages: 2

Brand: HBM Pages: 88

MP23xxxiec Series

Brand: YASKAWA Pages: 102

Brand: O&O Pages: 64

Brand: GSD Pages: 2

Neon 2000 Family

Brand: UniData Communication Systems Pages: 23

Brand: salmson Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands