GSSI SIR 4000 Manual Download | Manualshive

Page: 11 / 163

background image

Geophysical Survey Systems, Inc.

SIR® 4000

Manual

MN72-433 Rev F

5

Power Status LED:

When the system is turned on the indicator light will flash red. When the system is

ready the LED will remain a solid red.

Control Knob:

Cycles through the menu tree, quickly changes numeric values, and makes selections.

•

Turning the knob clockwise moves down through a menu or numeric values. Turning the knob
counter-clockwise moves up through a menu or numeric values.

•

Pressing the knob either toggles between On/Off options or enables a secondary menu. After
modifying the secondary option a second press of the knob locks-in the selection.

Directional Keypad:

This grouping of five buttons is located right below the wheel. The Enter button is

in the center. These buttons allow you to navigate through the menu tree and make selections.

•

Move through the menus by pressing the Up or Down buttons.

•

Pressing the Enter button either toggles between On/Off options or enables a secondary menu.

•

Modify the menu setting by using either the Up, Down, Left, or Right buttons.

•

After modifying the secondary option a second press of the Enter button locks-in the selection.

Back Button:

Returns to the main screen from whichever menu is currently selected or open.

Start Button:

Begin data collection.

•

Short press begins data collection (disabled during data collection).

•

Long press during data collection ends collection of the current file and immediately opens a new
one or prompts you to save or discard the current file.

Stop Button:

End data collection or playback.

•

Short press stops data collection.

•

Long press ends data collection or playback and return to the main menu.

«
...
9
10
11
12
13
...
»

Summary of Contents for SIR 4000




































































































































































Reviews:

No comments

Related manuals for SIR 4000

Brand: Echelon Pages: 40

Brand: Aalborg Pages: 15

Brand: Aalborg Pages: 48

Brand: Wavelink Pages: 69

Brand: Watts Pages: 2

Brand: Hanbay Pages: 18

Brand: Bard Pages: 8

Brand: Bardiani Valvole Pages: 35

FUTERA XLF Series

Brand: RBI Pages: 128

Brand: S&C Pages: 11

Brand: S&C Pages: 24

Brand: S&C Pages: 19

Brand: Mitsubishi Pages: 16

Brand: SOMFY Pages: 4

Brand: JASTEC Pages: 18

Brand: Sabiana Pages: 60

Brand: Whale Pages: 8

Brand: Tascam Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands