GSSI SIR 4000 Manual Download

Page: 142 / 163

Geophysical Survey Systems, Inc.

SIR® 4000

Manual

MN72-433 Rev F

136

A.2: Data Acquisition and Software

Data Format:

RADAN

(.dzt)

Output Data Format:

32 bit

Scan Rate:

Maximum 400 scans/sec at 256 samples/scan

Scan Interval:

User-selectable

Number Of Samples Per Scan:

256, 512, 1024, 2048, 4096, 8192, 16,384

Operating Modes:

Time- (Continuous), Distance- (Survey Wheel), or Point-Based Collection

Time Range:

1-20,000 nanoseconds full scale, user selectable

Gain:

Manual or automatic gain, 1-8 points, (-40 to +120 dB)

Standard Real-Time Filters:

•

Vertical: FIR Low-Pass, FIR High-Pass, IIR Low-Pass, and IIR High-Pass

•

Horizontal: FIR Stacking, FIR Background Removal, IIR Stacking, and IIR Background Removal

Advanced Real-Time Filters:

Migration, Surface Position Tracking, Signal Noise Floor Tracking, and

Hilbert Transform.

Automatic System Setups:

Storage of an unlimited number of system setup files for different survey

conditions and/or antenna deployment configurations.

Automatic Antenna Recognition:

Automatic recognition of Smart Antennas to allow maximum

compliant transmit rate.

A.3: System Includes

Digital Control Unit (DC-4000) with preloaded operating system (1)

Transit Case (1)

Batteries (2)

Charger (1)

Sunshade (1)

Operation Manual (1)

GSSI Manual CD (1)

Fully FCC , RSS-220, and CE Compliant.

Summary of Contents for SIR 4000




































































































































































Search results

Summary of Contents for SIR 4000

Reviews:

Related manuals for SIR 4000

Brands by name

Popular brands

GSSI SIR 4000, Manual

Search results

Summary of Contents for SIR 4000

Reviews:

Related manuals for SIR 4000

Brands by name

Popular brands