GSSI SIR 4000 Manual Download | Manualshive

Page: 102 / 163

background image

Geophysical Survey Systems, Inc.

SIR® 4000

Manual

MN72-433 Rev F

96

•

Power Mode can be set to 0, 50 or 60.

o

Power Mode is a passive detection method that can locate the AC current
of energized cables that are under load. These frequencies are typically
50Hz or 60Hz.

•

Frequency Mode can be set to 1, 8, 16, or 33 KHz.

o

Frequency Mode is an active detection method used in combination with a user-supplied
signal application device. Set the value of Frequency Mode to match the frequency of the
applied signal.

Radar Menu: 350HS (350MHz HyperStacking antenna)

1

Collect Mode:

Set to Distance.

2

Scans/Second.

The number of scans the

system will collect per second. The SIR
4000 will collect minimum of 1 and
maximum of 400 scans/second.

Samples/Scan

If you are collecting

distance-based data with a survey wheel, this
number represents the maximum possible
collect rate. If you exceed this maximum
rate the over-speed beeps will sound. It is
recommended that the scans/second be set
lower as lower scan rates will auto stack and
improve the signal to noise ratio.

For example: Scans/Second is set to 60 and you
have configured the system to collect 60 scans a
foot. If you move more than one foot per second
the system will attempt to collect scans which
are not available. Assuming your Antenna
Transmit Rate is 200 KHz, the scans/second
should be at least 240 whenever you are
collecting with a survey wheel and are collecting
a maximum of 512 Samples/Scan.

If you set Scans/Second higher than the selected transmit rate and the number of samples/scan, the SIR
4000 will lower it to the maximum possible. However, it is recommended that the scans/second be set
lower than the maximum. This will allow the system to auto stack points thereby improving the signal to
noise ratio.

3

Samples/Scan

Each scan curve is made up of individual data points, called Samples. More samples generate a smoother
scan curve and improve vertical resolution. This also affects scan speed; more points collected means
lower maximum scans/second.

•

You can choose from a preset list of 256, 512, 1024, 2048, 4096, 8192, or 16384 samples/scan.
Samples/Scan settings that are unavailable (due to conflicts with other settings) are greyed out.
FIR filters should only be used with 256-2048 samples/scan.

•

As sample number increases, max scan rate drops and file size increases.

«
...
100
101
102
103
104
...
»

Summary of Contents for SIR 4000




































































































































































Reviews:

No comments

Related manuals for SIR 4000

Brand: Quickmill Pages: 3

Brand: Samson Pages: 73

Brand: U.S. Divers Pages: 22

FEBCO 860 Small Series

Brand: Watts Pages: 12

Brand: Bardiani Valvole Pages: 54

Brand: Parker Pages: 478

Brand: Absima Pages: 5

RDS17S-ELITE1-R1

Brand: D&R ELECTRONICS Pages: 12

iDual A E27 iD60

Brand: jedi LIGHTING Pages: 23

VLTAutomationDrive FC 360

Brand: Danfoss Pages: 52

Brand: LOGICDATA Pages: 23

Brand: National Instruments Pages: 22

Brand: FMS Pages: 9

Brand: SIEB & MEYER Pages: 119

TITAN-TRACKSIDE-6

Brand: RC System Pages: 4

Q.PEAK DUO XL-G11S.X / BFG Series

Brand: Qcells Pages: 26

Brand: EpiSensor Pages: 37

Brand: Potter Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands