GSSI SIR 4000 Manual Download | Manualshive

Page: 75 / 163

background image

Geophysical Survey Systems, Inc.

SIR® 4000

Manual

MN72-433 Rev F

69

compresses the colors towards zero (0). A Color Stretch less than one (1) expands the colors towards the
maximum negative and positive amplitudes.

Left Color Stretch = 0; Middle Color Stretch = 1; Right Color Stretch = 3

Color Slide:

Selecting Color Slide allows you to shift the center point of the selected Colormap over a

scan’s amplitude range. A negative number shifts towards the positive amplitudes and positive number
shifts towards the negative amplitudes.

•

Adjusting the Color Slide over a particular value range allows you to see more subtle variations in
the data.

Left Color Slide = -0.20; Middle Color Slide = 0; Right Color Slide = 0.20

Rotate:

You can rotate the grid from 0-358º using the Control Knob. The rotation changes in increments

of 2º and you can start by moving up from zero or down from 358º. Combining Rotate with Viewpoint
can create a 3D view of the data during collection.

Viewpoint:

Viewpoint adjusts the perspective

to view the grid. You can adjust the Viewpoint
from -0.40 to 1, where -0.40 will provide almost
a straight forward view of a 2D profile as you
would see during 2D data collection. This will
not preview through the Output menu unless
Viewpoint Toggle was selected from the
Toolbar.

Home:

Resets Rotate and Viewpoint to zero (0).

Marks on Grid:

This turns the grid marks on or

off. Grid marks correspond with the location of
the profiles in the grid. Only adds marks to the
lines where data have already been collected.

File Info:

This opens a window showing the

current settings including Radar Parameters, Positioning information, and Processing History.

4.7 GPS Enabled 3D Collection

Connect a GPS unit to collect a georeferenced 3D grid on the SIR 4000.

Step 1: Connect and Configure GPS

Connect the GPS to your SIR 4000 using the serial connection on the top of the control unit. From the
Introduction Screen select GPS from the Toolbar. Set the Baud Rate to match the GPS unit’s Baud Rate
and choose the desired Format to view your location information.

«
...
73
74
75
76
77
...
»

Summary of Contents for SIR 4000




































































































































































Reviews:

No comments

Related manuals for SIR 4000

Brand: Samson Pages: 92

Brand: Jafar Pages: 10

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 12

Brand: Danfoss Pages: 60

Brand: Danfoss Pages: 20

Elemec3 013-02-0095-002

Brand: GAI-Tronics Pages: 12

Brand: Garmin Pages: 220

Brand: Gardena Pages: 16

Brand: jcm-tech Pages: 8

Brand: Kärcher Pages: 4

Brand: National Instruments Pages: 14

Brand: National Instruments Pages: 31

Brand: National Instruments Pages: 50

Brand: National Instruments Pages: 24

Brand: National Instruments Pages: 21

Brand: National Instruments Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands