GSSI SIR 4000 Manual Download

Page: 74 / 163

Geophysical Survey Systems, Inc.

SIR® 4000

Manual

MN72-433 Rev F

Gain:

Increase or decrease the Display Gain during data collection by a factor ranging from -12-60 dB.

This can be used to adjust contrast for an entire profile by the same amount.

Output Menu

This menu provides options for modifying the appearance of your data during collection.
The first six (6) options are the same for 3D collection as they are for 2D collection. None
of these setting affect the raw data.

H Cursor:

Changes the depth of the slice map in the Grid Display in half inch increments.

Slice Thickness:

Adjusts the slice thickness from zero (0) inches to the maximum

selected depth range in half inch increments. The slice is centered on the location of the
H Cursor.

Dielectric:

You can adjust the Dielectric Constant during data collection from a value of

one (1) to eighty-one (81).

Colormap:

This menu option offers 30 available Colormap options (i.e. color tables).

Select the menu by pressing the Control Knob or Enter key and then scroll through
Colormap #0-29.

Color Stretch:

Selecting Color Stretch allows you to adjust how the selected Colormap is

distributed over a scan’s amplitude range. A Color Stretch greater than one (1)

Summary of Contents for SIR 4000




































































































































































Search results

Summary of Contents for SIR 4000

Reviews:

Related manuals for SIR 4000

Brands by name

Popular brands

GSSI SIR 4000, Manual

Search results

Summary of Contents for SIR 4000

Reviews:

Related manuals for SIR 4000

Brands by name

Popular brands