GE L60 Instructions Manual Download Page 327 | Manualshive

Page: 327 / 768

background image

CHAPTER 5: SETTINGS

PRODUCT SETUP

L60 LINE PHASE COMPARISON SYSTEM – INSTRUCTION MANUAL

5-119

5

The relay measures current demand on each phase, and three-phase demand for real, reactive, and apparent power.
Current and Power methods can be chosen separately for the convenience of the user. Settings are provided to allow the
user to emulate common electrical utility demand measuring techniques, for statistical or control purposes. If the

CRNT

DEMAND METHOD

is set to "Block Interval" and the

DEMAND TRIGGER

is set to “Off,” Method 2 is used as follows. If

DEMAND

TRIGGER

is assigned to any other FlexLogic operand, Method 2a is used as follows.

The relay can be set to calculate demand by any of the following three methods.

5.3.11.1 Calculation method 1: Thermal exponential

This method emulates the action of an analog peak-recording thermal demand meter. The relay measures the quantity
(RMS current, real power, reactive power, or apparent power) on each phase every second and assumes that the circuit
quantity remains at this value until updated by the next measurement. It calculates the 'thermal demand equivalent'
based on the following equation:

Eq. 5-6

where
d = demand value after applying input quantity for time t (in minutes)
D = input quantity (constant)
k = 2.3 / thermal 90% response time
The figure shows the 90% thermal response time characteristic of 15 minutes. A setpoint establishes the time to reach
90% of a steady-state value, just as the response time of an analog instrument. A steady state value applied for twice the
response time indicates 99% of the value.

Figure 5-50: Thermal demand characteristic

5.3.11.2 Calculation method 2: Block interval

This method calculates a linear average of the quantity (RMS current, real power, reactive power, or apparent power) over
the programmed demand time interval, starting daily at 00:00:00 (that is, 12:00 am). The 1440 minutes per day is divided
into the number of blocks as set by the programmed time interval. Each new value of demand becomes available at the
end of each time interval.

5.3.11.3 Calculation method 2a: Block interval (with start demand interval logic trigger)

This method calculates a linear average of the quantity (RMS current, real power, reactive power, or apparent power) over
the interval between successive Start Demand Interval logic input pulses. Each new value of demand becomes available at
the end of each pulse. Assign a FlexLogic operand to the

DEMAND TRIGGER

setting to program the input for the new

demand interval pulses.



DEMAND INTERVAL:

15 MIN

Range: 5, 10, 15, 20, 30, 60 minutes



DEMAND TRIGGER:

Off

Range: FlexLogic operand

Note: for calculation using method 2a

«
...
325
326
327
328
329
...
»

Summary of Contents for L60

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for L60

615 Series ANSI

Brand: ABB Pages: 60

Brand: Samson Pages: 92

Brand: Jafar Pages: 10

Brand: Kasco Pages: 3

Brand: Danfoss Pages: 7

Brand: Xantrex Pages: 56

Brand: Xantrex Pages: 2

Freedom Sequence

Brand: Xantrex Pages: 58

Brand: Xantrex Pages: 4

Brand: Xantrex Pages: 20

Brand: York Pages: 24

Brand: Waterway Pages: 8

Brand: Black Horse Model Pages: 19

Brand: Reliance Foundry Pages: 3

Brand: Wesa Pages: 8

Brand: UniPOS Pages: 6

Brand: Belimo Pages: 2

Brand: zeeltronic Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands