manualshive.com logo in svg

GE L60, Instructions Manual

The GE L60 is a highly efficient and reliable device designed to meet your diverse power generation needs. To ensure optimal operation, it is vital to have its user-friendly Instruction Manual. You can download this comprehensive manual for free at manualshive.com, allowing you to take full advantage of your GE L60's features and functionalities.

Share
Download
background image

9-22

L60 LINE PHASE COMPARISON SYSTEM – INSTRUCTION MANUAL

OVERVIEW

CHAPTER 9: THEORY OF OPERATION

9

This dual phase-comparison scheme can be modified to operate over a two-frequency, frequency-shift channel by 
eliminating AND3, FDL, NOT1, and the center frequency. The transmitter can then be arranged to send the low-shift 
frequency continuously except when keyed by the positive SQ. AMP to the high shift frequency. This arrangement, though 
simpler than the three-frequency scheme, is deemed to be less secure.
The following illustrates a dual phase-comparison blocking scheme using a two-frequency, frequency-shift channel. Since 
one or the other of the two frequencies must be on at all times, and since both are blocking frequencies, there appears to 
be little need for an FDL function. Thus, it is not included. When the transmitter is not keyed, it sends low-shift continuously 
and when it is keyed by the negative squaring amplifier, it shifts to high for the negative half-cycle. This scheme is simpler 
than that of the previous scheme but probably is not as secure.

Figure 9-14: Dual phase-comparison blocking scheme

There does not appear to be a good purpose for a three-frequency channel in dual phase-comparison blocking schemes 
because the center frequency does not add to security or otherwise improve performance.
Note that a dual phase-comparison scheme using an ON-OFF channel has to be a combined blocking and tripping 
scheme. During one polarity of half-cycle, it has to trip on absence of any received signal (blocking), and on the other 
polarity of half-cycle it has to trip in the presence of the received signal.
In general, it can be concluded that dual phase-comparison can be accomplished in the blocking and in the tripping 
modes. The overall performance of the scheme depends on the characteristics of the channel selected. While dual phase-
comparison reduces the maximum tripping time, it does so at the expense of simplicity and possibly some security 
depending on how it is accomplished.

9.1.7  Refinements to basic schemes

There are a number of standard refinements that are required and normally included in all phase comparison schemes. 
These are discussed in terms of the basic blocking scheme of Figure 9-4, but apply generally to all schemes, sometimes in 
a different form.

Summary of Contents for L60

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for L60

J4C 20 Mounting Instructions preview
20
Brand: J4C Pages: 4
ABB ACH550 series Quick Start Manual preview
ACH550 series
Brand: ABB Pages: 6
jbc DI Series Manual preview
DI Series
Brand: jbc Pages: 4
IBM 2702 Information Manual preview
2702
Brand: IBM Pages: 105
Panasonic FP2 Series Technical Manual preview
FP2 Series
Brand: Panasonic Pages: 68
Panasonic GP-KS162CUDE Operating Instruction preview
GP-KS162CUDE
Brand: Panasonic Pages: 27
Panasonic EBL512 G3 5000 Planning Instructions preview
EBL512 G3 5000
Brand: Panasonic Pages: 168
Panasonic WV-CU980 Software Update Procedure preview
WV-CU980
Brand: Panasonic Pages: 8
Panasonic AW-RP50 Manual preview
AW-RP50
Brand: Panasonic Pages: 3
Panasonic FP0H Series Operation Manual preview
FP0H Series
Brand: Panasonic Pages: 20
Panasonic AK-HRP1010G Operating Manual preview
AK-HRP1010G
Brand: Panasonic Pages: 29
Panasonic AK-HRP1005G Operation Manual preview
AK-HRP1005G
Brand: Panasonic Pages: 37
Panasonic AG-EC4G Operating Instructions Manual preview
AG-EC4G
Brand: Panasonic Pages: 9
QCON ProX Setup preview
ProX
Brand: QCON Pages: 4
Baccara G75-DFC Installation Operation & Maintenance preview
G75-DFC
Brand: Baccara Pages: 16
Farfisa TD6100 Manual preview
TD6100
Brand: Farfisa Pages: 20
Racal Instruments 1266 Manual preview
1266
Brand: Racal Instruments Pages: 64
National Instruments SCC-DO01 User Manual preview
SCC-DO01
Brand: National Instruments Pages: 14

Brands by name

Popular brands

Load more brands