GE auisys cs2 User'S Reference Manual Download Page 256

Page: 256 / 268

•

When the liquid level indicator reaches the full mark, slowly
remove the bottle from the filling port.

Removing the bottle quickly may cause the agent to splash or
squirt out of the filling port.

Put the cap back on the filling port.

Put the cap back on the agent bottle.

Filling with Saf-T-Fill bottle

AB.60.050

AB.60.049

Figure 13-8 • Aladin2 cassette with Saf-T-Fil mechanism

Do not store filled or partially filled desflurane cassettes

above the normal working temperature of 35C/95F.

Storage at high temperature may cause the overpressure

valve to vent desflurane vapor into the ambient air.

Do not open or press the cassette filling port of the gas

connection valves with fingers or any kind of instrument.

Anesthetic agent liquid or gas may squirt into the air.

Note

WARNING

•

Aisys CS²

13-14

2067226-001

Summary of Contents for auisys cs2













































































































































































































































































Search results

Summary of Contents for auisys cs2

Reviews:

Related manuals for auisys cs2

Brands by name

Popular brands

GE auisys cs2, User'S Reference Manual

Search results

Summary of Contents for auisys cs2

Reviews:

Related manuals for auisys cs2

Brands by name

Popular brands