manualshive.com logo in svg

GE auisys cs2, User'S Reference Manual

The GE Auisys CS2 User's Reference Manual is a comprehensive guide packed with all the necessary information to effortlessly operate your device. This well-structured manual can be downloaded for free from our website, allowing you to access it anytime, anywhere. Enhance your user experience with our downloadable manual at manualshive.com.

Share
Download
background image

Super user mode

Do not enter Super User mode when a patient is

connected to the system. Gas flow will cease, and the

system must be powered down in order to restart gas

flow.

Changes made in Super User mode affect the system

configuration. All changes made are permanent and

preserved until changed again.

Several settings can be changed in Super User mode. These
changes should only be made by the person responsible for the
configuration of the system.

To access the Super User mode, select 

System Setup

 and then

Super User

. The Super User mode is password protected. Contact

the sales representative to obtain the password.

The system must be turned off to exit Super User mode.

Menu items are dependant on system configuration. Inactive menu
items are gray and are not selectable.

The menu selections shown in the examples are the factory default
values. The available settings are shown to the right of the menu.

WARNING

•

Note

Note

Aisys CS²

12-2

2067226-001

Summary of Contents for auisys cs2













































































































































































































































































Reviews:

No comments

Related manuals for auisys cs2

Rath 2100 Installation & Operation Manual preview
2100
Brand: Rath Pages: 3
GE ImageQuant LAS 4000 Original Instructions Manual preview
ImageQuant LAS 4000
Brand: GE Pages: 86
GE AKTApure Operating Instructions Manual preview
AKTApure
Brand: GE Pages: 160
GE AKTA avant Getting Started preview
AKTA avant
Brand: GE Pages: 134
DARAY X200 Operating & Installation Manual preview
X200
Brand: DARAY Pages: 28
MacDon 3020 Operator'S Manual preview
3020
Brand: MacDon Pages: 88
Jiffy 56 Operating Manual/Parts Manual preview
56
Brand: Jiffy Pages: 15
Panasonic DVCPRO P2 Series Brochure & Specs preview
DVCPRO P2 Series
Brand: Panasonic Pages: 32
ACE INSTRUMENTS AFM-5 Quick Start Manual preview
AFM-5
Brand: ACE INSTRUMENTS Pages: 2
ODA LP Series User Manual preview
LP Series
Brand: ODA Pages: 103
Above All MT Instruction Manual preview
MT
Brand: Above All Pages: 4
Barreto 20RTK Operator'S Manual preview
20RTK
Brand: Barreto Pages: 20
Barreto 13STKH Owner'S Manual preview
13STKH
Brand: Barreto Pages: 18
Backyard Discovery Premier Series Manual preview
Premier Series
Brand: Backyard Discovery Pages: 41
Ecco Pro Vantage 12+ Series Mounting Instructions preview
Pro Vantage 12+ Series
Brand: Ecco Pages: 6
Varytec Derby User Manual preview
Derby
Brand: Varytec Pages: 5
Saab R60 User Manual preview
R60
Brand: Saab Pages: 98
Kaixin DCU10 User Manual preview
DCU10
Brand: Kaixin Pages: 89

Brands by name

Popular brands

Load more brands