manualshive.com logo in svg

GE auisys cs2, User'S Reference Manual

The GE Auisys CS2 User's Reference Manual is a comprehensive guide packed with all the necessary information to effortlessly operate your device. This well-structured manual can be downloaded for free from our website, allowing you to access it anytime, anywhere. Enhance your user experience with our downloadable manual at manualshive.com.

Share
Download
background image

Message

Priority

Cause

Action

EtSev high

Medium

EtSev is greater than alarm limit. The
alarm priority escalates to High if the
alarm is not resolved after 2 minutes.

Set the alarm limits appropriately.
Check agent setting.

EtSev low

Low

EtSev is less than alarm limit.

Check the fill level of the vaporizers. Set
alarm limit appropriately. Check agent
setting.

FiCO2 high.
Absorbent OK?

High

FiCO2 is greater than alarm limit.

Check if absorbent needs to be
changed.

FiDes high

Medium

FiDes is greater than alarm limit. The
alarm priority escalates to High if the
alarm is not resolved after 2 minutes.

Set the alarm limits appropriately.
Check agent setting.

FiDes low

Low

FiDes is less than alarm limit.

Check the fill level of the vaporizers. Set
alarm limit appropriately. Check agent
setting.

FiEnf high

Medium

FiEnf is greater than alarm limit. The
alarm priority escalates to High if the
alarm is not resolved after 2 minutes

Set the alarm limits appropriately.
Check agent setting.

FiEnf low

Low

FiEnf is less than alarm limit.

Check the fill level of the vaporizers. Set
alarm limit appropriately. Check agent
setting.

FiHal high

Medium

FiHal is greater than alarm limit. The
alarm priority escalates to High if the
alarm is not resolved after 2 minutes

Set the alarm limits appropriately.
Check agent setting.

FiHal low

Low

FiHal is less than alarm limit.

Check the fill level of the vaporizers. Set
alarm limit appropriately. Check agent
setting.

FiIso high

Medium

FiIso is greater than alarm limit. The
alarm priority escalates to High if the
alarm is not resolved after 2 minutes

Set the alarm limits appropriately.
Check agent setting.

FiIso low

Low

FiIso is less than alarm limit.

Check the fill level of the vaporizers. Set
alarm limit appropriately. Check agent
setting.

FiO2 high

Medium

FiO2 is greater than high alarm limit.

Check the O2 setting. Recalibrate the
O2 cell and the airway module.

FiO2 low

High

FiO2 is less than low alarm limit.

Check O2 setting. Check for leaks or
blockages in the patient circuit.

FiSev high

Medium

FiSev is greater than alarm limit. The
alarm priority escalates to High if the
alarm is not resolved after 2 minutes

Set the alarm limits appropriately.
Check agent setting.

FiSev low

Low

FiSev is less than alarm limit.

Check the fill level of the vaporizers. Set
alarm limit appropriately. Check agent
setting.

For mech vent,
set Bag/Vent
switch

Low

Bag/Vent switch is set to Bag and the
ACGO switch is set to Circle.

Move switch to Vent position to start
mechanical ventilation.

Gas monitoring
not available

Medium

Airway module hardware failure.

Replace airway module. Then, turn
power off and back on between cases
to clear the alarm and receive module
data.

Aisys CS²

7-8

2067226-001

Summary of Contents for auisys cs2













































































































































































































































































Reviews:

No comments

Related manuals for auisys cs2

C.M.O FL Series Instruction And Maintenance Manual preview
FL Series
Brand: C.M.O Pages: 10
Pari mini Instructions For Use Manual preview
mini
Brand: Pari Pages: 50
Icare HOME Instruction Manual preview
HOME
Brand: Icare Pages: 42
Oakworks Medical PG Series Instruction & Maintenance Manual preview
PG Series
Brand: Oakworks Medical Pages: 28
Landoll 7430 Series Operator'S Manual preview
7430 Series
Brand: Landoll Pages: 70
Landice R9 Owner'S Manual preview
R9
Brand: Landice Pages: 19
Landice ElliptiMill Assembly Instructions Manual preview
ElliptiMill
Brand: Landice Pages: 7
Kärcher SP 16.000 Dirt Manual preview
SP 16.000 Dirt
Brand: Kärcher Pages: 148
Bayer HealthCare Certegra Operation Manual preview
Certegra
Brand: Bayer HealthCare Pages: 104
Energizer EDC2-1001-RGB-MWT Quick Start Manual preview
EDC2-1001-RGB-MWT
Brand: Energizer Pages: 18
MIETHKE proGAV Instructions For Use Manual preview
proGAV
Brand: MIETHKE Pages: 125
Stamina 35-1050 Owner'S Manual preview
35-1050
Brand: Stamina Pages: 22
Tripp Lite P130-06N-AUDIO Owner'S Manual preview
P130-06N-AUDIO
Brand: Tripp Lite Pages: 24
ABB HT588579 Operation Manual preview
HT588579
Brand: ABB Pages: 136
ABB HT598319 Operation Manual preview
HT598319
Brand: ABB Pages: 108
Beckman Coulter Optima LE-80K Instruction Manual preview
Optima LE-80K
Brand: Beckman Coulter Pages: 52
Copernicus Royal RC005 Assembly Manual preview
Royal RC005
Brand: Copernicus Pages: 13
Emos ZYP0201 Quick Start Manual preview
ZYP0201
Brand: Emos Pages: 8

Brands by name

Popular brands

Load more brands