manualshive.com logo in svg

GE auisys cs2, User'S Reference Manual

The GE Auisys CS2 User's Reference Manual is a comprehensive guide packed with all the necessary information to effortlessly operate your device. This well-structured manual can be downloaded for free from our website, allowing you to access it anytime, anywhere. Enhance your user experience with our downloadable manual at manualshive.com.

Share
Download
background image

Auto limits

Use the 

Auto Limits

 menu to quickly set alarm ranges for ‘MV’, ‘TV’,

and ‘EtCO2’ during mechanical ventilation.

Setting auto limits

1.

Select 

Auto Limits

.

The menu shows the current measured values and the
proposed low and high alarm limits.

2.

Check the proposed parameters.

•

Select 

Confirm

 to use the proposed low and high alarm

limits.

•

Select 

Cancel

 to leave the alarm limits unchanged.

•

Select 

Case Default Limits

 to set the alarm limits to the

case default limits.

The proposed low and high alarm limits are shown in highlighted
text. The alarm limits that are not highlighted do not change.

--

Note

3 Operation

2067226-001

3-9

Summary of Contents for auisys cs2













































































































































































































































































Reviews:

No comments

Related manuals for auisys cs2

Ecco 10 Series Mounting Instructions preview
10 Series
Brand: Ecco Pages: 3
NAD M52 Owner'S Manual preview
M52
Brand: NAD Pages: 10
KaVo 9010 Instructions For Use Manual preview
9010
Brand: KaVo Pages: 49
Easson EX-100 Manual preview
EX-100
Brand: Easson Pages: 33
Xiitech 1060 Operation Intructions preview
1060
Brand: Xiitech Pages: 6
Macht Dental POWER CLEAN Operation Instruction Manual preview
POWER CLEAN
Brand: Macht Dental Pages: 8
NanoVibronix UROSHIELD Quick Manual preview
UROSHIELD
Brand: NanoVibronix Pages: 2
NanoVibronix PainShield User Manual preview
PainShield
Brand: NanoVibronix Pages: 32
Nanoleaf Shapes Hexagons User Manual preview
Shapes Hexagons
Brand: Nanoleaf Pages: 27
Quark-Elec QK-A031 Setup Manual preview
QK-A031
Brand: Quark-Elec Pages: 2
Vahterus Plate User Manual preview
Plate
Brand: Vahterus Pages: 31
Garmin FUSION APOLLO MS-WB675 Installation Instructions Manual preview
FUSION APOLLO MS-WB675
Brand: Garmin Pages: 18
Rapid Shape RS wash Quick Start Manual preview
RS wash
Brand: Rapid Shape Pages: 12
Hanskamp MultiFill 003-561-005 Installation And Operating Instructions Manual preview
MultiFill 003-561-005
Brand: Hanskamp Pages: 20
EFX EFF523 Instructions For Use preview
EFF523
Brand: EFX Pages: 2
Nano Temper Monolith NT.115 User Manual preview
Monolith NT.115
Brand: Nano Temper Pages: 24
MetalTech SCAFFOLDBENCH I-CISRL Operational Safety And Assembly Instructions preview
SCAFFOLDBENCH I-CISRL
Brand: MetalTech Pages: 16
EditorsKeys Portable Vocal Booth Pro Studio Series Instruction Sheet preview
Portable Vocal Booth Pro Studio Series
Brand: EditorsKeys Pages: 2

Brands by name

Popular brands

Load more brands