GE auisys cs2 User'S Reference Manual Download Page 96

Page: 96 / 268

Aladin cassette installation

Using the liquid level indicator, check that the cassette is filled to
the appropriate level.

If using Aladin2, unlock the cassette handle before installing it
into the active bay.

Insert the cassette into the active bay until a click is heard. An
audible click indicates that the cassette is in position.

Turn the lock on the handle to the horizontal position (Aladin2
cassettes only).

The cassette is properly inserted when the agent is identified on
the display. Make sure that the displayed agent matches the
cassette.

Store the cassettes in the cassette storage bay when they are not in
use. See the "

Vaporizer cassettes

" section for additional cassette

information.

Note

Aisys CS²

5-2

2067226-001

Summary of Contents for auisys cs2













































































































































































































































































Search results

Summary of Contents for auisys cs2

Reviews:

Related manuals for auisys cs2

Brands by name

Popular brands

GE auisys cs2, User'S Reference Manual

Search results

Summary of Contents for auisys cs2

Reviews:

Related manuals for auisys cs2

Brands by name

Popular brands