GAC MOTOR Trumpchi Owner'S Manual Download Page 216

Page: 216 / 255

210

6. Use and maintenance

CAUTION

● The wiper arm can be pulled up

only after it is adjusted to the wiper

maintenance mode.

● Do not open the hood when the wiper is

pulled up, otherwise the hood and wiper

arm will be damaged.

● When pulling up the wiper arm, please

hold the wiper arm by hand instead of

the soft wiper blade.

● New wiper blades with the same length

and specifications must be used.

● Be careful when lowering the wiper arm

to prevent it from falling and hitting the

windshield instantly.

● The status of wiper blades must be

checked regularly and replaced as

required. Damaged wiper blades must

be replaced in time.

● Excessive worn or dirty wiper blades

are easy to scratch the windshield, and

will affect the field of vision and reduce

driving safety during use.

6.4.5 Brake fluid

Brake fluid function

Brake fluid is used to transmit power in the

vehicle hydraulic brake system.
The brake fluid is water-absorbent and

it continuously absorb moisture in the

surrounding air during use. If the brake fluid

remains in the system for a long time and the

water absorption is too high, air resistance will

be generated in the system pipeline during

braking, which will reduce the braking effect,

affect the driving safety, and even lead to

complete failure of the brake system, causing

accidents. Therefore, be sure to go to the GAC

Motor authorized shop to check the brake fluid

level or change the brake fluid according to the

period specified in the

Warranty Manual

NOTE

Brake fluid specification: DOT4.

WARNING

● The use of waste brake fluid or

improper brake fluid will greatly

reduce the braking effect and even

cause brake system failure! The

company does not assume any

liability (including warranty) for

vehicle failure and damage caused

thereby.

● Compliant brake fluid must be used

and must be new.

Brake system indicator lamp

When the vehicle is running, if the indicator

lamp

is red and the instrument cluster

displays the message “Please add brake fluid”,

stop the vehicle at a safe place immediately

and check whether the brake fluid level is

normal.

Summary of Contents for Trumpchi
































































































































































































































































Search results

Summary of Contents for Trumpchi

Reviews:

Related manuals for Trumpchi

Brands by name

Popular brands

GAC MOTOR Trumpchi, Owner'S Manual

Search results

Summary of Contents for Trumpchi

Reviews:

Related manuals for Trumpchi

Brands by name

Popular brands