GAC MOTOR Trumpchi Owner'S Manual Download Page 118

Page: 118 / 255

112

4. Operation of systems and equipment

Enter the local music playback interface in the

following ways:
-

Enter the local music interface by clicking

on the “Meida” card in the main interface.

Press the sound source switching button

on the right side of the steering wheel

repeatedly to switch to the local music

interface.

Click the “Local Music” soft key in the

application menu interface to enter the

local music interface.

NOTE

The AV system only supports USB devices

in FAT16/32, exFAT and NTFS formats, and

supports lossless music.

Sound source selection

Pause/Playback

Playlist

Search entry

Previous track

Next track

Cycle mode

Sound effect setting

4.6.4 Local music

Summary of Contents for Trumpchi
































































































































































































































































Search results

Summary of Contents for Trumpchi

Reviews:

Related manuals for Trumpchi

Brands by name

Popular brands

GAC MOTOR Trumpchi, Owner'S Manual

Search results

Summary of Contents for Trumpchi

Reviews:

Related manuals for Trumpchi

Brands by name

Popular brands