Fujitsu ABHG18KRTA Service Manual Download Page 262

Page: 262 / 471

2-30. E: 74. Outdoor temperature thermistor error (Outdoor unit)

Indicator

Indoor unit

Operation indicator

7 time flash

Timer indicator

4 time flash

Economy indicator

Continuous flash

Error code

E: 74

Detective actuator

Outdoor unit main PCB

When outdoor temperature thermistor open or short
circuit is detected at power on or while running the
compressor

Outdoor temperature thermistor

Forecast of cause

Connector failure

Thermistor failure

Main PCB failure

Check point 1. Check connection of connector

•

Check if connector is loose or removed.

•

Check erroneous connection.

•

Check if thermistor cable is open

-> Reset power when reinstalling due to removed connector or incorrect wiring.

↓

Check point 2. Remove connector and check thermistor resistance value

•

For the outdoor temperature thermistor resistance value, refer to

"Thermistor re-

sistance values"

on page 03-94.

•

If thermistor is either open or shorted, replace it and reset the power.

↓

Check point 3. Check voltage of main PCB

Make sure circuit diagram of outdoor unit and check terminal voltage at thermistor
(DC 5.0 V).

NOTE:

For details of thermistor connector, refer to

"Wiring diagrams"

in Chapter 2.

TECHNICAL DATA AND PARTS LIST on page 02-117.

If the voltage does not appear, replace main PCB.

↓

End

2-30. E: 74. Outdoor temperature thermistor error (Outdoor unit)

- (03-46) -

2. Troubleshooting with error code

TROUBLESHOOTING

Summary of Contents for ABHG18KRTA
























































































































































































































































































































































































































































































Search results

Summary of Contents for ABHG18KRTA

Reviews:

Related manuals for ABHG18KRTA

Brands by name

Popular brands

Fujitsu ABHG18KRTA, Service Manual

Search results

Summary of Contents for ABHG18KRTA

Reviews:

Related manuals for ABHG18KRTA

Brands by name

Popular brands