Fujitsu ABHG18KRTA Service Manual Download Page 410

Page: 410 / 471

Press the MODE button once to transmit the function mode information.

Press the

button once to transmit the function setting information. 2 short beeps will be

emitted from the indoor unit when the signal is received correctly. If wrong code is set, no beep
sound will be emitted.

2 short beeps

NOTE:

Press

button within 30 seconds after pressing MODE button.

For the function details, refer to

Chapter 1-5. "Function details"

on page 05-38.

Exit the function setting mode by pressing the RESET button.

RESET



Setting up each indoor unit

Repeat step from 1. to 8. to set up each indoor unit. If the custom code is other than " ", steps from
1. to 2. and 8. need to be performed.

1-2. Indoor unit (setting by wireless remote controller)

- (05-6) -

1. Function settings (for indoor unit)

FIELD

WORKING

FIELD

WORKING

Summary of Contents for ABHG18KRTA
























































































































































































































































































































































































































































































Search results

Summary of Contents for ABHG18KRTA

Reviews:

Brands by name

Popular brands

Fujitsu ABHG18KRTA, Service Manual

Search results

Summary of Contents for ABHG18KRTA

Reviews:

Brands by name

Popular brands