manualshive.com logo in svg

Fuji Xerox DocuPrint CM225FW, User Manual, Page: 34 / 344

Share
Download
Fuji Xerox DocuPrint CM225FW User Manual Download Page 34

34

Basic Operation

Printing a Panel Settings Page

Using the Operator Panel

1

Press the 

 (

System

) button.

2

Select 

Report

 

/

 

List

.

3

Select 

Panel Settings

.

4

Select 

Print

.

The Panel Settings page is printed.

Using the Printer Setting Utility (Windows Only)

The following procedure uses Microsoft

®

 Windows

®

 7 as an example.

1

Click 

Start

 

 

All Programs

 

 

Fuji Xerox

 

 

Fuji Xerox Printer Software for Asia-Pacific

 

 your printer 

 

Printer Setting Utility

.

NOTE: 

•

The window to select a printer appears in this step when multiple print drivers are installed on your computer. In this 
case, click the name of the desired printer listed in 

Printer Name

.

The Printer Setting Utility appears.

2

Click the 

Printer Settings Report

 tab.

3

Select 

Reports

 from the list at the left side of the page.

The 

Reports

 page is displayed.

4

Click 

Panel Settings

.

The Panel Settings page is printed.

Summary of Contents for DocuPrint CM225FW

























































































































































































































































































































































Reviews:

No comments