manualshive.com logo in svg

Fuji Xerox DocuPrint CM225FW, User Manual, Page: 285 / 344

Share
Download
Fuji Xerox DocuPrint CM225FW User Manual Download Page 285

Troubleshooting

285

Auger Mark

NOTE: 

•

If the problem continues even though you have taken suggested actions described above, contact the Fuji Xerox local 
representative office or an authorized dealer.

Problem

Action

The printed result has auger mark.

The toner cartridges may be low or need to be replaced. Confirm the amount of 
toner in each toner cartridge.

1

Check the toner level in the 

Status

 tab in the 

Printer Status

 window of the 

SimpleMonitor.

2

Replace the toner cartridges as necessary.

Start 

Clean Developer

.

1

Launch the Printer Setting Utility, and click 

Clean Developer

 on the 

Diagnosis

 

tab.

2

Click 

Start

.

Summary of Contents for DocuPrint CM225FW

























































































































































































































































































































































Reviews:

No comments