Fuji Xerox DocuPrint CM225FW User Manual Download Page 198

Page: 198 / 344

198

Faxing

Setting Sounds



Speaker Volume

Press the

(

System

) button.

Select the

Tools

tab, and then select

Admin Settings

Select

Fax Settings

Select

Fax Line Settings

Select

Line Monitor

Select the desired volume, and then select

Reboot the printer by turning the power switch off and then on.



Ringer Volume

Press the

(

System

) button.

Select the

Tools

tab, and then select

Admin Settings

Select

Fax Settings

Select

Incoming Defaults

Select

Ring Tone Volume

Select the desired volume, and then select

Reboot the printer by turning the power switch off and then on.

Summary of Contents for DocuPrint CM225FW
























































































































































































































































































































































Search results

Summary of Contents for DocuPrint CM225FW

Reviews:

Fuji Xerox DocuPrint CM225FW, User Manual, Page: 198 / 344

Search results

Summary of Contents for DocuPrint CM225FW

Reviews: