Fuji Xerox DocuPrint CM225FW Page 162 User Manual Download

Page: 162 / 344

162

Scanning



Sending the Scanned File to the Network

Load the document(s) facing up with top edge in first into the ADF or place a single document facing down on
the document glass.

See also:

•

"Making Copies From the ADF" on page 130

•

"Making Copies From the Document Glass" on page 128

Press the

(

Services Home

) button.

Select

Scan To

Select

Network

Select

until the desired address appears and then select that address.

Select

Select scanning options as required.
For details, see "Scan Defaults" on page 244.

Press the

(

Start

) button to send the scanned files.

When you are using the document glass, the display prompts you for another page. Select

Scan Another

Page

Done. Upload Now

If you want to place a new document, replace the document with a new document, and then select

Scan

Another Page

Summary of Contents for DocuPrint CM225FW
























































































































































































































































































































































Search results

Summary of Contents for DocuPrint CM225FW

Reviews:

Related manuals for DocuPrint CM225FW

Brands by name

Popular brands

Fuji Xerox DocuPrint CM225FW, User Manual

Search results

Summary of Contents for DocuPrint CM225FW

Reviews:

Related manuals for DocuPrint CM225FW

Brands by name

Popular brands