manualshive.com logo in svg

Fuji Xerox DocuPrint CM225FW, User Manual, Page: 302 / 344

Share
Download
Fuji Xerox DocuPrint CM225FW User Manual Download Page 302

302

Troubleshooting

Wi-Fi Direct Problems

Problem

Action

The device cannot discover the 
printer.

The printer may be connected to another device via Wi-Fi Direct

®

. Disconnect the 

printer and the device. For details, see "Disconnecting Wi-Fi Direct Network" on 
page 118.

The printer cannot disconnect from 
the device even when the procedure 
in "Disconnecting Wi-Fi Direct 
Network" has been performed.

The device may be automatically reconnecting to the printer. Reset the 
passphrase for Wi-Fi Direct and disconnect the device. For details, see "Resetting 
the Passphrase" on page 118.

The network mode of the printer 
cannot be set to 

Ad-Hoc

 mode on 

the CentreWare Internet Services.

Make sure that 

Wi-Fi Direct

 is set to 

Disable

.

Wi-Fi Direct

 cannot be set to 

Enable

.

Make sure that the network mode is set to 

Infrastructure

 mode on the 

CentreWare Internet Services.

Summary of Contents for DocuPrint CM225FW

























































































































































































































































































































































Reviews:

No comments