Fuji Electric FRENIC-MEGA, Instruction Manual

Page: 199 / 358

5-80
Ch
ap
. 5
FUNCTION C
O
DES
E codes
Function code data
Terminal commands assigned Symbol
Drive control
Related
function codes
Active ON Active OFF V/f PG
V/f
w/o
PG
w/
PG
Torque
control
26 1026
Enable auto search for idling motor
speed at starting
STM
Y Y Y N Y H09, d67
1030 30 Force to stop
STOP
Y Y Y Y Y F07, H56
32 1032 Pre-excitation
EXITE
N N Y Y N H84, H85
33 1033
Reset PID integral and differential
components
PID-RST
Y Y Y Y N
J01 to J19,
J56 to J62
34 1034 Hold PID integral component
PID-HLD
Y Y Y Y N
35 1035 Select local (keypad) operation
LOC
Y Y Y Y Y
(See Section
4.2.2.)
36 1036 Select motor 3
M3
Y Y Y Y Y A42, b42
37 1037 Select motor 4
M4
Y Y Y Y Y A42, r42
39
⎯
Protect motor from dew condensation
DWP
Y Y Y Y Y J21
40
⎯
Enable integrated sequence to switch to
commercial power (50 Hz)
ISW50
Y Y N N N
J22
41
⎯
Enable integrated sequence to switch to
commercial power (60 Hz)
ISW60
Y Y N N N
47 1047 Servo-lock command
LOCK
N N N Y N J97 to J99
48
⎯
Pulse train input
(available only on terminal [X7])
PIN
Y Y Y Y Y
F01, C30,
d62, d63
49 1049
Pulse train sign
(available on terminals except [X7])
SIGN
Y Y Y Y Y
70 1070 Cancel constant peripheral speed control
Hz/LSC
Y Y Y Y N
d41
71 1071
Hold the constant peripheral speed
control frequency in the memory
LSC-HLD
Y Y Y Y N
72 1072
Count the run time of commercial
power-driven motor 1
CRUN-M1
Y Y N N Y
H44, H94
73 1073
Count the run time of commercial
power-driven motor 2
CRUN-M2
Y Y N N Y
74 1074
Count the run time of commercial
power-driven motor 3
CRUN-M3
Y Y N N Y
75 1075
Count the run time of commercial
power-driven motor 4
CRUN-M4
Y Y N N Y
76 1076 Select droop control
DROOP
Y Y Y Y N H28
77 1077 Cancel PG alarm
PG-CCL
N Y N Y Y
⎯
80 1080 Cancel customizable logic
CLC
Y Y Y Y Y
E01 to E07,
U81 to U85
81 1081 Clear all customizable logic timers
CLTC
Y Y Y Y Y
98
⎯
Run forward
(Exclusively assigned to [FWD] and
[REV] terminals by E98 and E99)
FWD
Y Y Y Y Y
F02
99
⎯
Run reverse
(Exclusively assigned to [FWD] and
[REV] terminals by E98 and E99)
REV
Y Y Y Y Y
100
⎯
No function assigned
NONE
Y Y Y Y Y U81 to U85
Some negative logic (Active OFF) commands cannot be assigned to the functions marked with "
⎯
" in the "Active
OFF" column.
The "Enable external alarm trip" (data = 1009) and "Force to stop" (data = 1030) are fail-safe terminal commands.
In the case of "Enable external alarm trip," when data = 1009, "Active ON" (alarm is triggered when ON); when
data = 9, "Active OFF" (alarm is triggered when OFF).