Fuji Electric FRENIC-MEGA, Instruction Manual

Page: 138 / 358

5-19
Code Name Data setting range
Ch
an
ge
wh
e
n
ru
nning
Dat
a
cop
yi
ng
Default
setting
Drive control
Refer
to
page:
V/f
PG
V/f
w/o
PG
w/
PG
Torque
control
b28 (Iron loss factor 2) 0.00% to 20.00%
Y Y1 Y2 0.00 Y Y Y Y Y ―
b29 (Iron loss factor 3) 0.00% to 20.00%
Y Y1 Y2 0.00 Y Y Y Y Y
b30 (Magnetic saturation factor 1) 0.0% to 300.0%
Y Y1 Y2 *7 Y Y Y Y Y
b31 (Magnetic saturation factor 2) 0.0% to 300.0% Y Y1 Y2 *7 Y Y Y Y Y
b32 (Magnetic saturation factor 3) 0.0% to 300.0% Y Y1 Y2 *7 Y Y Y Y Y
b33 (Magnetic saturation factor 4) 0.0% to 300.0%
Y Y1 Y2 *7 Y Y Y Y Y
b34 (Magnetic saturation factor 5) 0.0% to 300.0%
Y Y1 Y2 *7 Y Y Y Y Y
b35 Motor 3
(Magnetic saturation extension
factor "a")
0.0% to 300.0%
Y Y1 Y2 *7 Y Y Y Y Y
b36 (Magnetic saturation extension
factor "b")
0.0% to 300.0%
Y Y1 Y2 *7 Y Y Y Y Y
b37 (Magnetic saturation extension
factor "c")
0.0% to 300.0% Y Y1 Y2 *7 Y Y Y Y Y
b39 Motor 3 Selection 0: Motor characteristics 0 (Fuji standard motors, 8-series)
1: Motor characteristics 1 (HP rating motors)
2: Motor characteristics 2 (Fuji motors exclusively designed
for vector control)
3: Motor characteristics 3 (Fuji standard motors, 6-series)
4: Other motors
N Y1 Y2 1 Y Y Y Y Y
b40 Slip Compensation 3
(Operating conditions)
0: Enable during ACC/DEC and at base frequency or
above
1: Disable during ACC/DEC and enable at base frequency
or above
2: Enable during ACC/DEC and disable at base frequency
or above
3: Disable during ACC/DEC and at base frequency or
above
N Y 0 Y Y N N N
b41 Output Current Fluctuation Damping
Gain for Motor 3
0.00 to 1.00
Y Y 0.20 Y Y N N N
b42 Motor/Parameter Switching 3
(Mode selection)
0: Motor (Switch to the 3rd motor)
1: Parameter (Switch to particular b codes)
N Y 0 Y Y Y Y Y 5-137
b43 Speed Control 3
(Speed command filter)
0.000 to 5.000 s
Y Y 0.020 N Y Y Y N ―
b44 (Speed detection filter) 0.000 to 0.100 s
Y* Y 0.005 N Y Y Y N
b45 P (Gain) 0.1 to 200.0 times
Y* Y 10.0 N Y Y Y N
b46 I (Integral time) 0.001 to 9.999 s
Y* Y 0.100 N Y Y Y N
b48 (Output filter) 0.000 to 0.100 s
Y Y 0.002 N Y Y Y N
b49 (Notch filter resonance frequency) 1 to 200 Hz
Y Y 200 N N N Y N
b50 (Notch filter attenuation level) 0 to 20 dB Y Y 0 N N N Y N
b51 Cumulative Motor Run Time 3 0 to 99990 hours
(The cumulative run time can be modified or reset.)
N N - Y Y Y Y Y
b52 Startup Counter for Motor 3 Indication of cumulative startup count
0 to 65535 times
Y N - Y Y Y Y Y
b53 Motor 3 (%X correction factor 1) 0% to 300% Y Y1 Y2 100 Y Y Y Y Y
b54 (%X correction factor 2) 0% to 300% Y Y1 Y2 100 Y Y Y Y Y
b55 (Torque current under vector control) 0.00 to 2000 A
N Y1 Y2 *7 N N Y Y Y
b56 (Induced voltage factor under
vector control)
50 to 100
N Y1 Y2 85 (90)
*8
N N Y Y Y
b57 Reserved *
9 ― - - - - - - - -
*7 The motor parameters are automatically set, depending upon the inverter's capacity. See Table B.
*8 85% for inverters of 150 HP or less; 90% for those of 175 HP or above.
*9 Factory use. Do not access these function codes.