manualshive.com logo in svg

EXFO FTB-860, User Manual

The EXFO FTB-860 is a versatile field-testing platform used for network infrastructure deployment and maintenance. Ensure optimal performance with the comprehensive User Manual available for free download on our website. Get the most out of your device by accessing the manual at manualshive.com.

Share
Download
background image

Index

NetBlazer

389

F

fabric status .............................................. 222
Factory Default

MAC .................................................... 299
Restore Default .................................... 325

FAIL ............................................................. 25
False Carrier............................................... 342
fault dist. (m/ft)......................................... 178
FCS ............................................................ 342
fibre channel test ...................................... 213
file type ..................................................... 261
Flow Control.............................................. 295
Follow Up.................................................. 194
frame

loss .................................................. 67, 68
size ........................................................ 71
type ....................................................... 70

Frame Count

Traffic .................................................. 344

frame count

RX................................................ 152, 274
TX ................................................ 152, 274

Frame Format............................................ 299
Frame Rate

Traffic .................................................. 344

Frame Type

Broadcast............................................. 345
Multicast.............................................. 345
Non-Unicast......................................... 345
Total .................................................... 345
Unicast ................................................ 345

Framing..................................................... 184
framing ....................................................... 46
Frequency.......................................... 298, 339

Offset .......................................... 297, 298
Step Size.............................................. 297

Frequency/Offset ....................................... 208
front panel, cleaning ................................. 355
Functions

Ping & Trace Route .............................. 350

G

Generated QL .................................... 204, 209
Global IPv6 Address (GUA) ........................ 311
global test duration estimate ...................... 42
GM Info ............................................. 187, 192
GM IP Address ........................................... 184

I

identification label..................................... 358
Identity .............................................. 187, 192
Idle ............................................ 190, 206, 341
idle ............................................................ 273
In Progress......................................... 190, 206
in progress................................................. 273
Inactive...................................................... 191
Information ............................................... 211
Information Count..................................... 208
Interface .................................................... 294
interface ID coupled .......................... 289, 312
Interface/Rate ............................................ 293
Internal Flash (Data) . 247, 249, 250, 265, 266, 

267

invert ......................................................... 235
IP ....................................................... 151, 274

Automatic IP (DHCP) ............................ 300

IP Address.................................................. 300
IP address .................................................. 166
IP Checksum .............................................. 340
IP Config - IPv6 .......................................... 310
IP TOS/DS................................................... 185

Ping ..................................................... 351

IPDV .......................................................... 195
IPDV Threshold .......................................... 188

J

Jabber........................................................ 342
jitter............................................................. 65
job information ......................................... 263

Summary of Contents for FTB-860


























































































































































































































































































































































































































Reviews:

No comments

Related manuals for FTB-860

ABB S4Cplus Instruction preview
S4Cplus
Brand: ABB Pages: 86
T-Drill F-400 Instruction Manual preview
F-400
Brand: T-Drill Pages: 75
Zeiss KS Instructions For Use Manual preview
KS
Brand: Zeiss Pages: 38
Taurus B450 Assembly Instructions Manual preview
B450
Brand: Taurus Pages: 28
Kärcher HDS Series Operator'S Manual preview
HDS Series
Brand: Kärcher Pages: 54
ABB 2 Series Operation And Installation Manual preview
2 Series
Brand: ABB Pages: 85
DARKSTAR TECHNOLOGIES D340 Manual To Operation preview
D340
Brand: DARKSTAR TECHNOLOGIES Pages: 4
TDW D2000 Maintenance Manuallines preview
D2000
Brand: TDW Pages: 2
Taurus 1170 Assembly And Operating Instructions Manual preview
1170
Brand: Taurus Pages: 25
Vancare G Series Quick Reference Manual preview
G Series
Brand: Vancare Pages: 3
Paitec ES-2000 User Manual preview
ES-2000
Brand: Paitec Pages: 14
Yamaha V50 Use Manual preview
V50
Brand: Yamaha Pages: 78
Fast 8200 Operation Manual preview
8200
Brand: Fast Pages: 42
DARAY V60 Manual preview
V60
Brand: DARAY Pages: 28
Backyard Play Systems 4500 Assembly Manual preview
4500
Brand: Backyard Play Systems Pages: 64
Haenim 3G Manual preview
3G
Brand: Haenim Pages: 2
Rangevision SPECTRUM Setup preview
SPECTRUM
Brand: Rangevision Pages: 28
Cameo SCUBA User Manual preview
SCUBA
Brand: Cameo Pages: 64

Brands by name

Popular brands

Load more brands