EXFO FTB-860 User Manual Download

Page: 254 / 409

CPRI/OBSAI Test Setup and Results

242

FTB-860/880

Test Functions - RTD

Delay

Indicates the time required for a bit to travel from the NetBlazer transmitter
back to its receiver after crossing a far-end loopback.



Last

indicates the result of the last RTD measurement.



Minimum

indicates the minimum RTD recorded.



Maximum

indicates the maximum RTD recorded.



Average

indicates the average RTD value.



Unit

measurement selections are

(default) and

Count

Indicates the total number of successful and failed measurements.

Successful

: A measurement is declared successful when the RTD is

smaller or equal to 2 seconds.

Failed

: A measurement is declared failed when the RTD is > 2 seconds.

Summary of Contents for FTB-860


























































































































































































































































































































































































































Search results

Summary of Contents for FTB-860

Reviews:

Related manuals for FTB-860

Brands by name

Popular brands

EXFO FTB-860, User Manual

Search results

Summary of Contents for FTB-860

Reviews:

Related manuals for FTB-860

Brands by name

Popular brands