manualshive.com logo in svg

EXFO FTB-860, User Manual

The EXFO FTB-860 is a versatile field-testing platform used for network infrastructure deployment and maintenance. Ensure optimal performance with the comprehensive User Manual available for free download on our website. Get the most out of your device by accessing the manual at manualshive.com.

Share
Download
background image

iv

FTB-860/880

7 RFC 2544 Test Setup and Results  ...............................................................73

Configuring an RFC 2544 Test ...............................................................................................74
Global Configuration  ............................................................................................................77
Subtests Configuration  .........................................................................................................80
Summary Results  ..................................................................................................................88
Graph ...................................................................................................................................96

8 EtherBERT Test Setup and Results ..............................................................99

Configuring a EtherBERT Test ..............................................................................................101
Global Configuration  ..........................................................................................................102
Summary Results  ................................................................................................................106

9 Traffic Gen & Mon Test Setup and Results  ..............................................111

Configuring a Traffic Gen & Mon Test  .................................................................................113
Global Configuration  ..........................................................................................................115
Streams Configuration ........................................................................................................116
Summary Results  ................................................................................................................125
Stream - Throughput Results  ..............................................................................................130
Stream - QoS Metrics Result  ...............................................................................................132
Traffic - Statistics Results .....................................................................................................136
Traffic - Flow Control Results  ..............................................................................................138

10 Through Mode Test Setup and Results  ....................................................141

Configure a Through Mode Test  .........................................................................................142
Summary Results  ................................................................................................................143
Traffic - Statistics Results .....................................................................................................145
Traffic - Flow Control Results  ..............................................................................................147

11 Smart Loopback Test Setup and Results  .................................................149

Configuring a Smart Loopback Test  ....................................................................................149
Summary Results  ................................................................................................................150
Third-Party Remote Loopback  .............................................................................................153

12 Ping Test Setup and Results  .....................................................................155

Configuring a Ping Test .......................................................................................................156
Global Configuration  ..........................................................................................................157
Summary Results  ................................................................................................................160

13 Trace Route Test Setup and Results  .........................................................163

Configuring a Trace Route Test  ...........................................................................................164
Global Configuration  ..........................................................................................................165
Summary Results  ................................................................................................................167

Summary of Contents for FTB-860


























































































































































































































































































































































































































Reviews:

No comments

Related manuals for FTB-860

FarmTek Growers Supply 109722 Manual preview
Growers Supply 109722
Brand: FarmTek Pages: 9
Quincy QR-25 Series Manual preview
QR-25 Series
Brand: Quincy Pages: 31
Quidel Lyme FIA Sofia 2 User Manual preview
Lyme FIA Sofia 2
Brand: Quidel Pages: 49
Quest Leisure Products Versailles Instructions Manual preview
Versailles
Brand: Quest Leisure Products Pages: 12
Raytec VARIO2 series Full Installation And Setup Manual preview
VARIO2 series
Brand: Raytec Pages: 60
Yuwell 7E-B5 Operation Instructions preview
7E-B5
Brand: Yuwell Pages: 2
Xylem McDonnell & Miller PSE-800-M Application, Installation, Operation, And Maintenance Manual preview
McDonnell & Miller PSE-800-M
Brand: Xylem Pages: 20
EuroLite SBPO-3240 Installation Instructions preview
SBPO-3240
Brand: EuroLite Pages: 2
Masalta MS100-4 Operation Manual preview
MS100-4
Brand: Masalta Pages: 13
Sailor 500 FleetBroadband User Manual preview
500 FleetBroadband
Brand: Sailor Pages: 20
My-Doc DocLaser Sport Quick Reference Manual preview
DocLaser Sport
Brand: My-Doc Pages: 32
Spitzer LIGHTING DSKL10-18WCC-S Installation Manual preview
DSKL10-18WCC-S
Brand: Spitzer LIGHTING Pages: 2
Cameo CLMFXBAR User Manual preview
CLMFXBAR
Brand: Cameo Pages: 56
Meyer Boss 8200 RT Owner/Operator’S Manual & Parts Book preview
Boss 8200 RT
Brand: Meyer Pages: 100
Orlit Rovelight RT-400 Manual preview
Rovelight RT-400
Brand: Orlit Pages: 16
AGCO Glencoe CM41 Operator'S Manual preview
Glencoe CM41
Brand: AGCO Pages: 44
Braun Aesculap S4 FW103R Instructions For Use/Technical Description preview
Aesculap S4 FW103R
Brand: Braun Pages: 39
Heitronic Sidra 501232 Installation And Operating Instructions Manual preview
Sidra 501232
Brand: Heitronic Pages: 8

Brands by name

Popular brands

Load more brands