Epson SC-F10000 Series User Manual Download Page 210

Page: 210 / 222

System Requirements

Each software can be used in the following environments. (As of February, 2021)

The supported operating systems may change.

For the latest information, see the Epson Web site.

Epson Edge Dashboard

The Epson Edge Dashboard can be used in the following environments.

Important:

Make sure the computer on which the Epson Edge Dashboard is installed meets the following requirements.

If these requirements are not met, the software cannot monitor the printer correctly.

❏

Disable your computer's hibernate function.

❏

Disable the sleep function so that the computer does not enter sleep status.

Windows

Operating systems

Windows 7 SP1 / Windows 7 x64 SP1

Windows 8 / Windows 8 x64

Windows 8.1 / Windows 8.1 x64

Windows 10 / Windows 10 x64

CPU

Multi-core processor (3.0 GHz or more recommended)

Free memory

4 GB or more

Hard disk
(free space during installation)

2 GB or more

Display resolution

1280 x 1024 or better

Communication interface

High Speed USB

Ethernet 1000Base-T

Browser

Internet Explorer 11

Microsoft Edge

Mac

Operating systems

Mac OS X 10.7 Lion or later

CPU

Multi-core processor (3.0 GHz or more recommended)

Free memory

4 GB or more

Hard disk
(free space during installation)

2 GB or more

SC-F10000H Series/SC-F10000 Series User's Guide

Appendix

210

Summary of Contents for SC-F10000 Series































































































































































































































Search results

Summary of Contents for SC-F10000 Series

Reviews:

Related manuals for SC-F10000 Series

Brands by name

Popular brands

Epson SC-F10000 Series, User Manual

Search results

Summary of Contents for SC-F10000 Series

Reviews:

Related manuals for SC-F10000 Series

Brands by name

Popular brands