manualshive.com logo in svg

Epson SC-F10000 Series, User Manual

Share
Download
Epson SC-F10000 Series User Manual Download Page 170

Problem Solver

When a Message is Displayed

If one of the following messages is displayed, read and follow the instructions below.

Messages

What to do

The waste ink bottle is nearing the end of
its service life.
Prepare a new one.
You can continue printing until
replacement is required.

The Waste Ink Bottle is getting full. Ready a new Waste Ink Bottle.

U

 

“Options and Consumable Products” on page 179

Ink cartridge is not recognized. Please
replace the cartridge.

Remove and reinsert the ink cartridge. If the message persists, insert a new ink
cartridge (do not reinsert the ink cartridge that caused the error).

Ink is low

You can continue printing until
replacement is required.

The ink is low. Confirm that a new ink cartridge is installed so the ink cartridges can
be automatically switched when the remaining amount falls below the threshold.

U

 

“Options and Consumable Products” on page 179

The heater is warming up.

One or more heaters is still being warmed to the specified temperature. To start
printing while the heater temperature is low, press 

Start

 to display a confirmation

screen, and then press 

OK

 to start.

The media and print head are contacting.
Check whether the print results are clean.
Printing can continue.

If you check the print results and they are dirty, stop printing and clean around the
print head.

U

 

“Cleaning Around the Print Head” on page 116

At the same time, refer to "Troubleshooting & Tips" in the 

Online Manual

 to take

measures so striking does not reoccur.

The XXXXX is nearing the end of its service
life.

The replacement interval is approaching for the parts that are shown. Prepare new
parts.

The media is not attached to the roll core
on the auto take-up reel unit.
Attach the media.

Media is not correctly attached to the Auto Take-up Reel Unit.

If this happens while printing, press 

Pause

 to stop printing.

Turn the Auto switch on the Auto Take-up Reel Unit to Off temporarily, return it to
the original settings, and then correctly install the media to the Auto Take-up Reel
Unit.

U

 

“Using the Auto Take-up Reel Unit” on page 77

The roll core is spinning.
Remove the media from the media holder,
and then reload the media.

Media is not correctly attached to the Media Feeding Unit.

Remove the media, and then correctly attach the media to the Media Feeding
Unit.

U

 

“Loading media” on page 70

The inside of the printer is hot.
Lower room temperature.

Lower the temperature of the room until it is within the temperature range
described in the “Specifications Table”.

U

 

“Specifications Table” on page 213

The media is low.

The remaining amount of loaded media is running low. Prepare new media.

SC-F10000H Series/SC-F10000 Series     User's Guide

Problem Solver

 

170

Summary of Contents for SC-F10000 Series































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands