Emerson Rosemount 3812 Maintenance And Troubleshooting Manual Download Page 50

Page: 50 / 132

Table 3-4: Split shroud removal tool list

Tools required

Standard 7/16 inch (11 mm) socket wrench or a standard 7/16 inch wrench

Appropriate personal protective equipment

Figure 3-12: Split shroud removal

A. Upper split shroud

B. Hex nuts with integral tooth lock washers and shroud clamps

C. Lower split shroud

Procedure

1. Using a 7/16 inch (11 mm) wrench, loosen and remove the four lower split shroud

hex nuts with integral tooth lock washers and shroud clamps (see

Figure 3-12

2. Remove the shroud clamps from each of the four studs by pulling the clamp off of

the ‘stud at each location.

3. Slide the lower split shroud down to remove it from the meter body.
4. Move the shroud assembly and bolts out of your immediate work area.

This completes the split shroud removal procedure.

3.4.4

Remove latched band shrouds

The latched band shroud is utilized on 2 inch to 10 inch ultrasonic flow meters.

Meter maintenance

Maintenance and Troubleshooting Manual

April 2022

00809-0100-3812

Emerson.com/Rosemount

Summary of Contents for Rosemount 3812





































































































































Search results

Summary of Contents for Rosemount 3812

Reviews:

Related manuals for Rosemount 3812

Brands by name

Popular brands

Emerson Rosemount 3812, Maintenance And Troubleshooting Manual

Search results

Summary of Contents for Rosemount 3812

Reviews:

Related manuals for Rosemount 3812

Brands by name

Popular brands