Emerson Rosemount 3812 Maintenance And Troubleshooting Manual Download Page 96

Page: 96 / 132

Figure 3-59: Backplane board replacement

A. Non-terminal end of Transmitter Electronics Enclosure

B. Power Supply board

C. I.S. Barrier board (inside the Guide Plate)

D. Backplane board

7. Use a 1/8 inch (3 mm) flat head screw driver and disconnect the Acquisition Cable

terminal block from the Backplane. Unplug the Acquisition Cable from the
Backplane.

8. Remove the Power Supply (if it was not removed with the Backplane board) and I.S.

Barrier boards from the enclosure. The I.S. Barrier Board has a notched tab that
secures the board to the Guide Plate.

9. Attach the Acquisition Cable terminal block to the new Backplane Board and plug

the Power Supply Board and I.S. Barrier board into the Backplane board.

10. Insert the Backplane (with the Power Supply and I.S. Barrier Boards attached to the

Backplane) into the enclosure.

11. Fully seat the CPU Module and Optional I/O Module onto the Backplane board.
12. Install the four Phillips head screws to secure the Backplane to the enclosure

standoffs.

13. Reinstall the terminal blocks on the CPU Module, Optional I/O Module, and the

Power Supply board using a 3 mm flat head screw driver.

Meter maintenance

Maintenance and Troubleshooting Manual

April 2022

00809-0100-3812

Emerson.com/Rosemount

Summary of Contents for Rosemount 3812





































































































































Search results

Summary of Contents for Rosemount 3812

Reviews:

Related manuals for Rosemount 3812

Brands by name

Popular brands

Emerson Rosemount 3812, Maintenance And Troubleshooting Manual

Search results

Summary of Contents for Rosemount 3812

Reviews:

Related manuals for Rosemount 3812

Brands by name

Popular brands