Emerson Rosemount 3812 Maintenance And Troubleshooting Manual Download Page 118

Page: 118 / 132

Figure 3-78: Transmitter electronic enclosure security seals

A. Transmitter Electronics Enclosure end cap

B. Security wire seals

3. Adjust the security wire, removing all slack and thread into the lead seal.
4. Cut wire ends to remove excess wire.

This completes installing the Transmitter Electronics Enclosure security wire seals.

3.11.2

Seal direct or remote mount Base electronics enclosure

Use the following instructions to install the security seal wire on the Base Enclosure.

Procedure

1. Install security wire seal into and through two of the four the holes in the socket

head screws on the Base Enclosure cover (maximum wire diameter .078 inch; 2.0
mm).

Meter maintenance

Maintenance and Troubleshooting Manual

April 2022

00809-0100-3812

118

Emerson.com/Rosemount

Summary of Contents for Rosemount 3812





































































































































Search results

Summary of Contents for Rosemount 3812

Reviews:

Related manuals for Rosemount 3812

Brands by name

Popular brands

Emerson Rosemount 3812, Maintenance And Troubleshooting Manual

Search results

Summary of Contents for Rosemount 3812

Reviews:

Related manuals for Rosemount 3812

Brands by name

Popular brands