Emerson Rosemount 3812 Maintenance And Troubleshooting Manual Download Page 122

Page: 122 / 132

Figure 3-82: Shroud security seals

A. Top end shroud

B. Security wire seals

Procedure

1. Install the security seal wire into and through the two bolt holes on the top end

shrouds (maximum wire diameter .078 inch; 2.0 mm). Position the wire to prevent
counterclockwise rotation of the screws when the seal wire is taut.

2. Remove all slack and seal.
3. Repeat previous step for the other top end shroud.
4. Cut wire ends to remove excess wire.

This completes the clamped band shroud security seal installation procedure.

Split shroud security seals

Use the following instructions to install the security seal wires on the split shroud covering
the meter body and transducer assemblies.

Meter maintenance

Maintenance and Troubleshooting Manual

April 2022

00809-0100-3812

122

Emerson.com/Rosemount

Summary of Contents for Rosemount 3812





































































































































Search results

Summary of Contents for Rosemount 3812

Reviews:

Related manuals for Rosemount 3812

Brands by name

Popular brands

Emerson Rosemount 3812, Maintenance And Troubleshooting Manual

Search results

Summary of Contents for Rosemount 3812

Reviews:

Related manuals for Rosemount 3812

Brands by name

Popular brands