Emerson Rosemount 3812 Maintenance And Troubleshooting Manual Download Page 102

Page: 102 / 132

Figure 3-62: Conduit removal

A. Transmitter electronics enclosure

B. Conduit gland fitting

4. If the meter is equipped with security seals, remove the seals from the bolts on the

Base Enclosure.

Figure 3-63: Transmitter Electronics Enclosure and Base Enclosure security seal
removal

A. Transmitter electronics enclosure

B. Base enclosure bolts and security seals

5. For direct mount electronics, Use a 7/16 inch (11mm) wrench and remove the four

hex head bolts and split lock washers securing the Transmitter Electronics Enclosure
to the Base Enclosure.

Meter maintenance

Maintenance and Troubleshooting Manual

April 2022

00809-0100-3812

102

Emerson.com/Rosemount

Summary of Contents for Rosemount 3812





































































































































Search results

Summary of Contents for Rosemount 3812

Reviews:

Related manuals for Rosemount 3812

Brands by name

Popular brands

Emerson Rosemount 3812, Maintenance And Troubleshooting Manual

Search results

Summary of Contents for Rosemount 3812

Reviews:

Related manuals for Rosemount 3812

Brands by name

Popular brands