Emerson Rosemount 3812 Maintenance And Troubleshooting Manual Download Page 65

Page: 65 / 132

Figure 3-25: Transmitter Electronics Enclosure and Base Enclosure removal

A. Transmitter electronics enclosure

B. Base enclosure bolts

C. Base electronics enclosure

5. Lift the Transmitter Electronics Enclosure off of the Base Enclosure to expose the

Acquisition Module wiring. Prop the Transmitter Electronics Enclosure on top of the
Base Enclosure and prepare to disconnect the Acquisition cable and transducer
terminal blocks.

6. Use a 1/8 inch (3mm) flat blade screw driver to remove the Acquisition cable

terminal block screws. Unplug the Acquisition cable terminal block.

7. Use a 1/8 inch (3mm) flat blade screw driver and remove the transducer wire

terminal blocks screws. Disconnect the transducer cable wires from the terminal
blocks so that the cables can be removed from the meter.

NOTICE

Ensure the transducer cables are labeled for the chord configuration (A1, A2, B1 and
B2).

Maintenance and Troubleshooting Manual

Meter maintenance

00809-0100-3812

April 2022

Rosemount 3812 Liquid Ultrasonic Flow Meter

Summary of Contents for Rosemount 3812





































































































































Search results

Summary of Contents for Rosemount 3812

Reviews:

Related manuals for Rosemount 3812

Brands by name

Popular brands

Emerson Rosemount 3812, Maintenance And Troubleshooting Manual

Search results

Summary of Contents for Rosemount 3812

Reviews:

Related manuals for Rosemount 3812

Brands by name

Popular brands