Emerson Rosemount 3812 Maintenance And Troubleshooting Manual Download Page 49

Page: 49 / 132

Figure 3-11: Band shroud hem bend joint

A. Front shroud hem joint

B. Back shroud hem joint

9. Repeat

Step 1

Step 8

to remove the other clamped band shroud parts.

10. Move all of the clamped band shroud parts, top end shrouds, bolts, lock washers,

and worm screw clamps out of your immediate work area.
This completes the clamped band shroud removal procedure.

3.4.3

Remove split shrouds

WARNING

SHARP EDGES - CUTTING HAZARD
Equipment may have sharp edges.
Wear safety approved gloves, eye protection and shoes when disassembling the shrouds.
Failure to comply may cause serious injury.

Maintenance and Troubleshooting Manual

Meter maintenance

00809-0100-3812

April 2022

Rosemount 3812 Liquid Ultrasonic Flow Meter

Summary of Contents for Rosemount 3812





































































































































Search results

Summary of Contents for Rosemount 3812

Reviews:

Related manuals for Rosemount 3812

Brands by name

Popular brands

Emerson Rosemount 3812, Maintenance And Troubleshooting Manual

Search results

Summary of Contents for Rosemount 3812

Reviews:

Related manuals for Rosemount 3812

Brands by name

Popular brands