Emerson Rosemount 3812 Maintenance And Troubleshooting Manual Download Page 83

Page: 83 / 132

Figure 3-49: Junction box disassembly

A. Junction box hex head bolts

B. Junction box cover and gasket

C. Terminal blocks

D. Terminal block mounting plate

E. Meter mount junction box

F. Nylon gasket and feed-thru foam cable seal

11. Use a 1/8 inch (3 mm) flat-blade screw driver and disconnect the transducer cable

wiring from the terminal blocks.

12. Remove the terminal blocks from the Junction box.
13. Use a flat blade screw driver and remove the terminal block mounting plate from

the junction box.

14. Use a 7/16 inch (11mm) socket wrench and remove the three hex head screws, split

lock washers, flat washers, shoulder washers and lift the Junction box off of the
meter body.

15. Prepare to install the new transducer and the cable assembly.
16. Make sure the cables are labeled for the correct transducer (A1, A2, B1, and B2).
17. Place one drop of Dow Corning 200 Silicon Oil (12,500 Centistokes) (P/N

1-360-01-650) on the face of the transducer to be installed.

Maintenance and Troubleshooting Manual

Meter maintenance

00809-0100-3812

April 2022

Rosemount 3812 Liquid Ultrasonic Flow Meter

Summary of Contents for Rosemount 3812





































































































































Search results

Summary of Contents for Rosemount 3812

Reviews:

Related manuals for Rosemount 3812

Brands by name

Popular brands

Emerson Rosemount 3812, Maintenance And Troubleshooting Manual

Search results

Summary of Contents for Rosemount 3812

Reviews:

Related manuals for Rosemount 3812

Brands by name

Popular brands