Emerson Rosemount 3812 Maintenance And Troubleshooting Manual Download Page 38 | Manualshive

Page: 38 / 132

background image

Table 3-1: Contents-Transducer maintenance

(continued)

Maintenance task

Description

Section

Install the shrouds

•

Band shroud options

•

Bolted shroud (2” -3”
meters)

•

Clamped shroud (12” and
larger)

•

Split shroud (4” to 10”
meters)

•

Latched shroud (2” to 10”
meters)

•

Shrouds installation

•

Install bolted band shrouds

•

Install clamped band shrouds

•

Install split shrouds

•

Install latched band shroud

Seal the meter

Seal the meter electronics and
transducers

•

Seal direct or remote mount
transmitter electronics
enclosure

•

Seal direct or remote mount
transmitter electronics
enclosure

•

Seal direct or remote mount
Base electronics enclosure

3.2

Important safety information

Follow these safety message instructions to avoid injury and equipment damage.

CAUTION

SURFACE TEMPERATURE HAZARD
Meter body and piping may be extremely hot or cold.
Wear appropriate personal protective equipment when coming in contact with the meter.
Failure to comply may result in injury.

CAUTION

TRANSPORTATION HAZARD
When moving the meter, do not insert the forks of a forklift into the bore.
Inserting the forks may cause the meter to become unstable, resulting in injury to
personnel or damage to the bore and sealing face.

CAUTION

TRIPPING HAZARD
Clear all obstacles or obstructions from the work area when transporting, installing or
removing the meter.
Failure to comply may cause injury to personnel.

Meter maintenance

Maintenance and Troubleshooting Manual

April 2022

00809-0100-3812

38

Emerson.com/Rosemount

«
...
36
37
38
39
40
...
»

Summary of Contents for Rosemount 3812





































































































































Reviews:

No comments

Related manuals for Rosemount 3812

Brand: DAKOTA ULTRASONICS Pages: 25

Brand: DAKOTA ULTRASONICS Pages: 36

Brand: OHAUS Pages: 84

SourceMeter 2400

Brand: Keithley Pages: 594

System SourceMeter 2601B

Brand: Keithley Pages: 864

Brand: Labgear Pages: 8

SourceMeter 2600B Series

Brand: Keithley Pages: 897

Brand: Sabre Pages: 13

Brand: YOSensi Pages: 26

Brand: YOSensi Pages: 26

Brand: PCB Piezotronics Pages: 17

Brand: Panasonic Pages: 1

FLEXFLO M4 Series

Brand: Blue-White Pages: 64

Brand: Dwyer Instruments Pages: 189

Brand: Lowrey Pages: 109

Brand: Bamo Pages: 17

Brand: Fluke Biomedical Pages: 28

Brand: VOLTCRAFT Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands